Heat&Glo TRUE-36-IFT Скачать руководство пользователя страница 60

Страница: 60 / 74

Heat & Glo • TRUE-36-IFT, TRUE-42-IFT, TRUE-50-IFT Installation Manual • 2461-980 Rev. Q • 11/20

H. Install the Log Assembly

LOG PLACEMENT INSTRUCTIONS

Log Set Assembly: LOGS-TRUE36

LOGS-TRUE42

Models: TRUE-36C, TRUE-36H, TRUE-36S, TRUE-36G-IFT, TRUE-36H-IFT, TRUE-36S-IFT, TRUE-36TG-IFT

TRUE-42C, TRUE-42H, TRUE-42S, TRUE-42G-IFT, TRUE-42H-IFT, TRUE-42S-IFT, TRUE-42TG-IFT

Log #1 (SRV2280-701 for TRUE-36, SRV2281-701 FOR TRUE-42)

: Locate log placement notch on the bottom of log #1.

See Figure 2. Mate outer notches on the bottom of Log #1 with the left and right grate tines. Slide Log #1 toward the rear

of appliance until back side of Log #1 contacts the log placement tabs. See Figures 1-3.

Figure 3.

Log #2 (SRV2280-702 for TRUE-36, SRV2281-702 for TRUE-42)

: Locate log placement notch on the bottom of Log #2.

See Figure 4. Mate notch on the bottom of Log #2 with the center and right grate tines. Slide log toward rear of appliance

until right end contacts the side grate tine. See Figure 5.

LOG PLACEMENT TABS

Figure 1.

Figure 2.

LOG PLACEMENT NOTCH

Figure 4.

Figure 5.

LOG PLACEMENT SLOTS

FLAT SPOT FOR LOG #3

NOTCH FOR LOG #6

BURNED AREA

LOG PLACEMENT NOTCH

LEFT SIDE TOWARD REAR

LOG CONTACTS

LOG CONTACTS
SIDE GRATE TINE

SIDE GRATE TINE

NOTCH FOR

NOTCH FOR
LOG #3

LOG #3

Log #2 (TRUE-36 ):

Log #2 will be about 1 inch from the

back of the center grate tine when properly placed. See

Figure 5.

Log #2 (TRUE-42 ):

Log #2 will contact center log placement

tab on center grate tine. See Figure 5.

TRUE-42 ONLY

Note:

Refractory appearance and material will vary depending on fireplace model.

CAUTION: Logs are fragile, handle with care.
NOTICE: If small chips and/or scratches are present, repair them using the included paint touch-up kit.

Содержание TRUE-36-IFT











































































Результаты поиска

Содержание TRUE-36-IFT

Отзывы:

Похожие инструкции для TRUE-36-IFT

Бренды по названию

Популярные бренды

Heat&Glo TRUE-36-IFT, Установка и настройка устройства

Результаты поиска

Содержание TRUE-36-IFT

Отзывы:

Похожие инструкции для TRUE-36-IFT

Бренды по названию

Популярные бренды