Heat&Glo TRUE-36-IFT Скачать руководство пользователя страница 55

Страница: 55 / 74

Heat & Glo • TRUE-36-IFT, TRUE-42-IFT, TRUE-50-IFT Installation Manual • 2461-980 Rev. Q • 11/20

D. Install Glass Refractory (TRUE-36G-IFT/

TRUE-42G-IFT Only)

CAUTION! Risk of Cuts or Abrasions. Wear protective
gloves and safety glasses during installation.

NOTICE: Handle refractory panels with care. Refractory
may chip or crack if dropped or impacted.

TOOLS

Screw gun equipped with 1/4 in. socket or
1/4 IN. wrench or socket

Utility Knife

Flat Screwdriver

REFRACTORY COMPONENTS

(1) Black Glass Left Panel
(1) Black Glass Right Panel
(1) Black Glass Rear Panel
(2) Finish Trim Pieces

(1) Top Refractory Panel

INSTALLATION

1. Remove glass from the front of the appliance. Re

move all shipping materials from inside the firebox.

See Figure 11.9.

Figure 11.9 Remove Shipping Materials

2. Carefully remove top refractory by straightening the

retaining tabs. Set refractory panel aside for later

use. See Figure 11.9.

3. Separate the shipping bracket from the log grate by

cutting the zip tie with a utility knife. See Figure 11.10

Figure 11.10 Separate Shipping Bracket from Log Grate

4. Bend shipping bracket up slightly, exposing the two

screws that retain the shipping bracket to the log

grate. Remove the screws and discard shipping

bracket. See Figure 11.11.

Figure 11.11 Remove Shipping Bracket

REMOVE SCREWS

5. Slide the two left base refractory pieces and one right

base refractory piece forward or remove completely.

See Figure 11.10.

6. Using a flat screwdriver, straighten hand bends on the

refractory tabs at the top of the side spacers (left and

right) to allow the side spacers to be moved forward

about three inches. See Figure 11.12.

REMOVE ALL SHIPPING MATERIALS

RETAINING TABS

SHIPPING BRACKET

CUT ZIP TIE

MOVE REFRACTORY

MOVE REFRACTORY
FORWARD OR REMOVE

FORWARD OR REMOVE

Содержание TRUE-36-IFT











































































Результаты поиска

Содержание TRUE-36-IFT

Отзывы:

Похожие инструкции для TRUE-36-IFT

Бренды по названию

Популярные бренды

Heat&Glo TRUE-36-IFT, Установка и настройка устройства

Результаты поиска

Содержание TRUE-36-IFT

Отзывы:

Похожие инструкции для TRUE-36-IFT

Бренды по названию

Популярные бренды