Heat&Glo TRUE-36-IFT Скачать руководство пользователя страница 53

Страница: 53 / 74

Heat & Glo • TRUE-36-IFT, TRUE-42-IFT, TRUE-50-IFT Installation Manual • 2461-980 Rev. Q • 11/20

TOP RETAINING RAIL NOTCH

GLASS FRAME NOTCH

Figure 11.4 Positioning Glass

Figure 11.6. Installing Glass

Replacing Fixed Glass Assembly

This fixed glass assembly is held in place by two side

clips, one top retaining rail and lower glass clips. The

TRUE36 has three lower glass clips and the TRUE42 and

TRUE50 have four lower glass clips. To remove clips, en

gage the spring clips with the tool and pull tool out slightly.

Rotate wrist left and right to disengage clip. The glass clip

tool is shown in Figure 11.1.
1. Tool is fastened to the lower right corner of the fire

place. Remove tool by removing one screw. If glass

clip removal tool becomes misplaced, a cotter pin re-

moval tool may be used.

2. Position the fixed glass assembly so that it is about

eight inches from the face of the appliance. See Fig

ure 11.4. An arch decorative front application will re

quire the glass to be installed at a steeper angle.

3. Center the fixed glass assembly from left to right in

side the top of the appliance opening.

The glass frame has tabs on the bottom that coincide

with the bottom glass clip location. The TRUE-36 has

three tabs and the TRUE-42 and TRUE-50 have four

tabs. If the glass is not centered, it cannot be installed

properly. Align the notch at the top center of the glass

frame assembly with the notch on the top retaining

rail. See Figure 11.5.

Figure 11.5 Align Notches

Figure 11.7. Securing Side Glass Clips

4. Install fixed glass assembly by lifting it up and sliding

it into the top retaining rail. Grasp the fixed glass as

sembly on the sides.

CAUTION! Risk of Injury! DO NOT

put fingers under

glass frame. Fingers may get pinched by glass frame
during installation.

6. Once the left and right glass clips are installed, en

gage the bottom clips by inserting the glass clip tool at

a sharp downward angle to get between the gap be-

tween the glass frame and the front bottom fireplace

lip. See Figure 11.8.

7. Return glass tool to its shipping location in the low

er right corner of the appliance and secure with one

screw.

5. Ensure the fixed glass assembly is situated tight

against the firebox face. Engage the left and right

glass clips using the glass clip tool. See Figure 11.7.

Figure 11.8. Securing Bottom Glass Clips

Once the glass is installed tightly into the top retainer

rail, push in the bottom so that the glass assembly

rests on the support tabs on the glass clip. See Fig

ure 11.6.

GRASP FRAME BY LIP THAT

GRASP FRAME BY LIP THAT
PROJECTS FROM GLASS. DO NOT

PROJECTS FROM GLASS. DO NOT
INSERT FINGERS UNDER RAIL.

INSERT FINGERS UNDER RAIL.

RAIL

LIP

Содержание TRUE-36-IFT











































































Результаты поиска

Содержание TRUE-36-IFT

Отзывы:

Похожие инструкции для TRUE-36-IFT

Бренды по названию

Популярные бренды

Heat&Glo TRUE-36-IFT, Установка и настройка устройства

Результаты поиска

Содержание TRUE-36-IFT

Отзывы:

Похожие инструкции для TRUE-36-IFT

Бренды по названию

Популярные бренды