Heat&Glo TRUE-36-IFT Скачать руководство пользователя страница 30

Страница: 30 / 74

Heat & Glo • TRUE-36-IFT, TRUE-42-IFT, TRUE-50-IFT Installation Manual • 2461-980 Rev. Q • 11/20

G. PVLP-SLP and PVI-SLP-B Information

This section provides specific detail for installation of

TRUE-36, TRUE-42, and TRUE-50 models with ap-

proved power vent kits. Follow instructions included with

the PVLP-SLP or PVI-SLP-B power vent kits.
See Table 4.2 below for approved Power Venting options

for TRUE models.

WARNING! Risk of Fire! Use ONLY Hearth & Home
Technologies-approved power venting systems with this
appliance. Use of power venting systems not approved

by Hearth & Home Technologies could cause fireplace to

overheat.

PVI-SLP-B

Baffle Adjustment Setting

TRUE-36
TRUE-42

TRUE-50

3 Holes Visible

Figure 4.16 Baffle Adjustment Location - PVI-SLP-B

ADJUSTMENT BOLT

INDICATOR BAR

ADJUSTMENT HOLES

Figure 4.17 Baffle Adjustment - PVI-SLP-B

Table 4.2

WARNING! Risk of Explosion! Follow instructions to set

draft flow. Incorrect setting could impair burner perfor

mance and/or cause delayed ignition.

PVLP-SLP

PVI-SLP-B

TRUE-36

APPROVED

TRUE-42

APPROVED

TRUE-50

APPROVED

Table 4.3

The power vent draft flow must be adjusted and set per

the specifications in Table 4.3. Refer to the instructions

provided with the PVLP-SLP and PVI-SLP-B for more

specific information.

Setting the PVLP-SLP Baffle Adjustment:

Note:

The air baffle may be adjusted after installation.

The baffle adjustment screw can be accessed by removing

the front cap cover.
• If the burner flames are short, active, and jumping, turn

the bolt counterclockwise (open). check the burner

flames and adjust the baffle again as necessary until

the flames are stable, strong, and steady.

• If the burner flames are tall, lifting, floating, and ghost

like, the baffle is too far open and MUST be closed.

Turn bolt clockwise.

• If the pilot continuously sparks and does not become

steady, the baffle may need to be opened. The require

ments in Table 4.3. must still be met.

Distance from PVLP-SLP

to Appliance

Allowable Baffle

Minimum

Maximum

2-15 ft.

1-1/2 in.

2-1/2 in.

16-39 ft.

Closed

1-1/2 in.

Greater than 40

Closed

PVI-SLP-B:

The baffle adjustment is measured using the

holes on the indicator bar of the PVI-SLP-B baffle.

This

bar raises as the baffle is opened and lowers as the baffle

is closed. Adjust the baffle by turning the screw located in

the motor enclosure. See Figure 4.16 and 4.17.

Table 4.4

Содержание TRUE-36-IFT











































































Результаты поиска

Содержание TRUE-36-IFT

Отзывы:

Похожие инструкции для TRUE-36-IFT

Бренды по названию

Популярные бренды

Heat&Glo TRUE-36-IFT, Установка и настройка устройства

Результаты поиска

Содержание TRUE-36-IFT

Отзывы:

Похожие инструкции для TRUE-36-IFT

Бренды по названию

Популярные бренды