Gigamon GigaVUE TA Series, Руководство по установке оборудования

Страница: 14 / 108

14 GigaVUE TA Series Hardware Installation Guide
Air Flow Direction
The air flow direction is from the front of the GigaVUE chassis to the rear. The
rear-mounted fans pull air from the front to the back of the chassis. For environments
with hot/cold aisles, install the chassis so the intake air at the front of the chassis is
cold.
AC and DC-Powered GigaVUE-TA10 Models
Gigamon provides both AC and DC-powered versions of the GigaVUE-TA10 Traffic
Aggregator. Refer to
Connecting -48V DC Power Supplies on page 54 for information
on connecting DC power supplies.
Table 1-1: GigaVUE-TA10 Ports
Port Description
Mgmt Use the Mgmt port for remote configuration of the GigaVUE-TA10 Traffic Aggregator over a 10/100/
1000 Ethernet network. Refer to Connecting Serial Console and Mgmt Ports on page 57 for
information on establishing a Telnet or SSH configuration session with the GigaVUE-TA10 Traffic
Aggregator.
Console Use the Console port for local configuration of the GigaVUE-TA10 Traffic Aggregator over a serial
connection. Refer to Access the Command-Line Interface over the console Port on page 58 for
information on establishing a serial configuration session with the GigaVUE-TA10 Traffic Aggregator
in a terminal window.
Ports x1..x24 or
Ports x1..x48 The GigaVUE-TA10 provides either 24 or 48 10Gb/1Gb ports, depending on the version. Each of the
10Gb/1Gb ports can be used as either a network (ingress) or tool (egress) port.
For details about the supported transceivers and cable type, refer to the “GigaVUE-OS Compatibility
and Interoperability Matrix” .
Refer to Port Licensing on page 63 for license information to expand the 24-port GigaVUE-TA10A to
48 ports, including the four 40Gb ports.
Ports q1..q4
(or as x49..x64)
GigaVUE-TA10 also includes four 40Gb ports (q1..q4). The 40Gb ports can be used as a 40Gb
ingress port, or, as a high-speed tool port for aggregated output to a matching 40Gb port on a
GigaVUE H Series node.
In addition, you can also configure card modes that let either two (q1..q2) or all four (q1..q4) of the
40Gb ports operate as four logical 10Gb ports (x49..x64). This is useful when deploying the
GigaVUE-TA10 in an environment that does not yet include 40Gb interfaces. Refer to
Configuring the
Card Mode on GigaVUE-TA10 on page 39 .
Once a 40Gb port has been configured to operate as four 10Gb ports, cable it to an optical patch
panel or breakout panel, which takes a 40Gb QSFP+ input from the GigaVUE-TA10 and splits it to
four independent 10Gb output ports. Refer to
Breakout Panels on page 41 .
The q1..q4 ports accept 40Gb QSFP+ connections using active-fiber QSFP+ SR or PLR4
transceivers.
The q1..q4 ports accept 40Gb BiDi transceivers (RX-only or full duplex). RX-only BiDi only supports
RX on network ports. Full Duplex (RX/TX) supports network and tool ports.
Refer to Port Licensing on page 63 for license information to expand the 24-port GigaVUE-TA10A to
48 ports, including the four 40Gb ports.
Transceivers For details about the supported transceivers and cable type, refer to the “GigaVUE-OS Compatibility
and Interoperability Matrix” .