GE Vivid S70 Скачать руководство пользователя страница 66 | Manualshive

Страница: 66 / 709

background image

Prepare the System for Use

3-2

Vivid S70 / S60

–

User Manual

BC092760-1EN

01

Site requirements

Only qualified physicians or ultrasound sonographers should
perform scans of patients for medical diagnostic reasons.
Request training, if needed. Ensure that unauthorized personnel
do not tamper with the system.

Service representatives authorized by GE Ultrasound will
unpack and install the system. Do not attempt to install the
system alone.

To carry out regular preventative maintenance refer to Chapter
‘System Care and Maintenance’ on

Maintain a clean environment. Turn off the circuit breaker before
cleaning the system. Refer to ‘System Care and Maintenance’
on

for cleaning instructions.

The ultrasound system must operate within the proper
environment and in accordance with the requirements described
in this section. Before using the system, ensure that the
requirements are met.

Optimal operation of the system can be obtained by
implementing the following requirements:

Power requirements

The ultrasound system uses a separate power outlet for 100–
240 VAC, 50/60 Hz.

WARNING

All the warnings in Chapter ‘Safety’ on

read and understood before operating the system.

WARNING

Operating the system with the wrong voltage range causes
damages, voiding the factory warranty.

«
...
64
65
66
67
68
...
»

Содержание Vivid S70






































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Vivid S70

MicroVersaTrip Plus

Бренд: GE Страницы: 20

Бренд: GE Страницы: 252

Бренд: Balanced Body Страницы: 12

Бренд: Eagle Pro Страницы: 6

Бренд: GE Страницы: 10

Бренд: Ecco Страницы: 2

Бренд: Landoll Страницы: 94

Бренд: Bang & Olufsen Страницы: 2

Бренд: made for movement Страницы: 51

Бренд: IDEAL Networks Страницы: 60

Бренд: IceCure Страницы: 104

Бренд: lancer Страницы: 3

Бренд: lancer Страницы: 12

Бренд: R2 Страницы: 26

Бренд: Quark-Elec Страницы: 2

LED Street Bar 16x3W RGB IP65

Бренд: Varytec Страницы: 9

Бренд: VARILITE Страницы: 8

EVENTPROFILE VL800

Бренд: Vari Lite Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды