GE Vivid S70 Скачать руководство пользователя страница 157 | Manualshive

Страница: 157 / 709

background image

PW and CW Doppler

Vivid S70 / S60

–

User Manual

5-21

BC092760-1EN

01

Using PW/CW Doppler modes

Alternative 1

1. Press

PW

or

CW

. A scanning screen is displayed with a

Doppler cursor on the 2D mode image and a Doppler
spectrum in the lower part of the screen.

2. Use the trackball to position the Doppler cursor line and in

PW the sample volume location over the area of interest.

3. In PW, adjust the

Sample Volume

.

NOTE: Sample

Volume

adjustment may affect the Scale, Frame

rate and LV rej. settings.

Alternative 2

1. Press

Cursor

on the control panel. A cursor line is displayed

on the 2D image.

2.  Select the cursor type on the Touch panel.
3.  With the trackball adjust the position of the cursor line.
4.  Press

PW

or

CW

.

Optimizing PW/CW Doppler modes

The use of preset gives optimum performance with minimum
adjustment. If necessary, the following controls can be adjusted
to further optimize the PW/CW modes display:

NOTE:

Refer to ‘Generating a new preset’ on page 12-90 about
creating presets

•

Adjust the

Active mode gain

to set the gain in the spectral

Doppler area.

•

Adjust

Low velocity reject

to reduce unwanted low velocity

blood flow and tissue movement.

•

In PW mode, adjust

Sample volume

to low setting for better

resolution, or higher setting to more easily locate the
disturbed flows. Adjustment of the Sample volume may
affect the PRF (Nyquist limit) settings.

•

Adjust the

Compress

setting to balance the effect of

stronger and weaker echoes and obtain the desired intensity
display.

«
...
155
156
157
158
159
...
»

Содержание Vivid S70






































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Vivid S70

Бренд: K&K Страницы: 8

Бренд: Rain Harvesting Страницы: 2

Бренд: Valmar Страницы: 78

Бренд: Valhalla Scientific Страницы: 64

Бренд: A.J.Antunes Страницы: 24

Бренд: B&G Страницы: 2

Бренд: TANNER Scientific Страницы: 44

Бренд: Abus Страницы: 8

Бренд: Parkside Страницы: 37

WEIDER SHAPE GLIDER WECR43062

Бренд: ICON Health & Fitness Страницы: 6

Бренд: Duracell Страницы: 2

Бренд: Ambu Страницы: 32

Бренд: Reichert Страницы: 28

Бренд: Blizzard Lighting Страницы: 24

Бренд: Sima Страницы: 22

ROBOPAC ECOPLAT

Бренд: AETNAGROUP Страницы: 41

Бренд: SAMCHULLY Страницы: 24

Бренд: ADJ Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды