GE Vivid S70 Скачать руководство пользователя страница 627 | Manualshive

Страница: 627 / 709

background image

Probe overview

Vivid S70 / S60

–

User Manual

13-11

BC092760-1EN

01

NOTE:

Non-GE probes may also bear the UDI mark and equivalent
information.

Intracardiac Ultrasound Catheters

The ICE ultrasound catheters are sterile, disposable, and
licensed for single use only.

The catheters are optimized for intracardiac scanning. The
catheters are a single-plane, 90-degree, wide-view imaging
format catheter device with 64 channels that can transmit and
receive data simultaneously.

With catheter, the physician can maneuver the imaging plane
located inside the catheter tip to see the region of interest. The
physician can steer the catheter to optimize tissue visualization.

The user can steer the tip of the catheter bidirectionally in two
planes: left/right and posterior/anterior. The active face of the
catheter faces anteriorly, and the scanning plane is longitudinal.

The reusable ICEcord-RS cable connects the catheter to the
Vivid S70 / S60 system.

NOTE:

The reusable ICEcord-RS cable is equivalent to the SwiftLink™
ICE probe catheter connector cable. This cable is designed
exclusively for use with the ICE ultrasound catheters on Vivid
S70 / S60.

The SoundStarTM 3D 10F, SoundStar eco 10F, and SoundStar
eco 8F ultrasound catheters are intended to operate when the
Vivid S70 / S60 is interfaced to the CartoSound. The SoundStar
3D 10F catheter may also be used on the Vivid S70 / S60
without the CartoSound interface.

The Acuson AcuNav 10F and AcuNav 8F are intended to be
used on the Vivid S70 / S60 without an additional interface.

CAUTION

Vivid S70 / S60 is designed for compatibility with commercially
available ICE catheters (AcuNav™ 10F, AcuNav 8F,
SoundStar™ 3D 10F, Soundstar eco 10F, Soundstar eco 8F).

Verify clearance of these devices prior to using them with the
Vivid S70 / S60 system.

CAUTION

Use special ‘Carto’ preset when connected to CartoSound
System and be careful when adjusting parameters to avoid
framerate lower than 30 frames per second.

«
...
625
626
627
628
629
...
»

Содержание Vivid S70






































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Vivid S70

Бренд: AAON Страницы: 36

Бренд: Gatekeeper Страницы: 8

Bure Rise & Go DB 56-309

Бренд: Gate Страницы: 8

Бренд: Gebhardt Anlagentechnik Страницы: 152

Бренд: Hach Страницы: 58

Бренд: Hach Страницы: 52

Бренд: IDS Страницы: 2

Бренд: Rational Страницы: 16

Бренд: TC Electronic Страницы: 14

Бренд: Access Страницы: 7

Бренд: VDO Страницы: 15

Бренд: VDO Страницы: 20

Бренд: ZOLL Страницы: 37

Бренд: Wacker Neuson Страницы: 34

Бренд: Wagan Страницы: 4

Бренд: Wachs Страницы: 22

Бренд: Ideal Heating Страницы: 16

Бренд: ICS Страницы: 156

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды