GE Vivid S70 Скачать руководство пользователя страница 441 | Manualshive

Страница: 441 / 709

background image

Connectivity

Vivid S70 / S60

–

User Manual

10-39

BC092760-1EN

01

Dataflow selection

Select a dataflow from the

Archive

screen (see Figure 10-5

) or configure the system with a

default

dataflow

from the Configuration management package as described
below.

Default dataflow selection

1. Press

Utility

/

Config

on the Touch panel and log on as

administrator if required.

2. Select the

Connectivity

category and

Dataflow

subgroup.

The

Dataflow

sheet is displayed (see Figure 10-21).

3. Select the desired dataflow in the

Dataflow

pull-down menu

and check the option

Default

.

4. Press

Config

to exit the Configuration management

package.

Figure 10-21. Default dataflow

In this scenario the data is transferred from the Vivid S70 / S60 to a dedicated EchoPAC Software Only
workstation over the Ethernet (either in a peer-to-peer connection with a crossover cable, or in a network).
The database from the EchoPAC Software Only is used as the master and images are stored directly to the
EchoPAC Software Only internal harddrive. In this configuration the system is just an intermediate
acquisition system which after completion of a study, will not contain any patient information, measurements
or images.
Up to four systems can be connected to one EchoPAC Software Only if the workstation has the EchoPAC
Share option enabled. A Vivid S70 / S60 using the 203 software can only connect to an EchoPAC Software
Only also using the 203 software. Older version Vivid S70 / S60 can connect via EchoPAC Share if
compatible with Sybase 16. Please contact your local GE representative to update software for Sybase 16
compatibility if required.

System and EchoPAC Software Only in a direct connect environment

1. Select a dataflow
2. Default option for the selected dataflow

«
...
439
440
441
442
443
...
»

Содержание Vivid S70






































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Vivid S70

Бренд: Ecco Страницы: 3

Бренд: Yamaha Страницы: 50

Бренд: A&D Страницы: 30

Бренд: DAKO Страницы: 25

Бренд: 3M ESPE Страницы: 50

Бренд: VACGEN Страницы: 13

Бренд: ParaBody Страницы: 3

Бренд: Valiani Страницы: 66

Бренд: OHAUS Страницы: 84

Бренд: Zimmer Страницы: 2

Бренд: ZipRip Страницы: 31

REBOUND DUAL ST

Бренд: Össur Страницы: 104

Бренд: Össur Страницы: 130

Бренд: Elenco Electronics Страницы: 12

Бренд: GRAVITY Страницы: 2

Бренд: Delfield Страницы: 2

Vetter QuickStrut

Бренд: Idex Страницы: 14

Бренд: Pixlip Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды