GE Vivid S70 Скачать руководство пользователя страница 686 | Manualshive

Страница: 686 / 709

background image

Peripherals

14-16

Vivid S70 / S60

–

User Manual

BC092760-1EN

01

View-X Direct

Activating View-X Direct

The View-X Direct button is available on the Utility page when
Direct Connection is enabled in Config (default=enabled). See
‘Enable Direct Connection’ on

for information related

to Direct Connection, if needed.

Figure 14-10. View-X Direct button on the Utility page

Typical Use Scenario

Prepare for examination:

•

If needed, load worklist using the worklist dataflow while
connected to the hospital network. It will still be available
offline. Pull up the patient from Local Archive.

•

If not using a network, start the exam with Patient name/ID
in Local Archive. Connect to the Epiphan DVI Broadcaster:

1. Connect the Epiphan DVI Broadcaster to the ultrasound

system with the crossover network cable.

2. Open the Utility tab and click View-X Direct to toggle on.

This activates the IP addresses that allow the Epiphan DVI
Broadcaster and the ultrasound system to communicate.

3.  Complete the study.
4.  Click View-X Direct to toggle off the setting.
5.  To transfer the study, connect back to the hospital network

and transfer the study/exam/patient from Local Archive as
needed.

NOTE:

The Epiphan DVI Broadcaster static IP address is
192.168.255.250 and the ultrasound system's underlying static
IP address when View-X Direct is enabled is 192.168.255.249.
These addresses cannot be changed while View-X Direct is

«
...
684
685
686
687
688
...
»

Содержание Vivid S70






































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Vivid S70

Relion 670 series

Бренд: ABB Страницы: 66

Бренд: Laica Страницы: 4

Бренд: Labnet Страницы: 2

Бренд: Keithley Страницы: 32

Бренд: jcb Страницы: 166

D-MAS HyperSat 2540

Бренд: DanMedical Страницы: 103

Бренд: Cameo Страницы: 64

Бренд: Cameo Страницы: 100

Бренд: CAME Страницы: 32

Бренд: Taylor Страницы: 60

Бренд: TANDBERG Страницы: 23

Бренд: OAKWORKS Страницы: 2

Бренд: Oakton Страницы: 2

Бренд: Oakton Страницы: 2

Бренд: O2matic Страницы: 4

Бренд: Qlight Страницы: 3

Бренд: qtran Страницы: 2

Бренд: Q-Optics Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды