GE Vivid S70 Скачать руководство пользователя страница 164 | Manualshive

Страница: 164 / 709

background image

Image Optimization

5-28

Vivid S70 / S60

–

User Manual

BC092760-1EN

01

Using Tissue Tracking

1. From TVI Mode, press

Tissue Tracking

.

2. Adjust

Tracking start

close to the R-peak.

3. Adjust

Tracking end

to end systole.

4. Use the trackball to position the ROI frame over the area to

be examined.

5. Press

Select

. The instruction

Size

should be highlighted in

the trackball status bar.

NOTE:

If the trackball control Pointer is selected, press

Trackball

to

be able to select between Position and Size controls.

6. Use the trackball to adjust the dimension of the ROI.

Optimizing Tissue Tracking

•

To reduce quantification noise (variance), the Nyquist limit
should be as low as possible, without creating aliasing. To
reduce the Nyquist limit, reduce the scale while in TVI.

•

To check for aliasing, freeze the loop and apply velocity
trace (Press

Freeze

and

Q-Analysis

), see also

‘Quantitative Analysis’ on

).

•

The main use of Tissue Tracking is to map positive systolic
displacements. This means that

Tracking start

and

Tracking end

controls should be adjusted to pick out the

systolic phase of the cardiac cycle. Adjust

Tracking start

close to the R-Peak. Adjust

Tracking end

to end systole,

typically near the T-wave.

NOTE:

Tissue Tracking on TEE acquisitions displays negative
displacements. Make sure

Invert

is selected to display

positive displacements.

•

Negative displacement can be mapped by pressing

Invert

.

Tracking start

and

Tracking end

must then be adjusted to

pick out the diastolic phase of the cardiac cycle.

•

The maximum displacement that is color-coded can be
adjusted using

Tracking scale

. If set too low, most of the

wall will show the color indicating maximum displacement. If
set too high, the maximum displacement color is never
reached.

•

Tissue Tracking provides velocity information only in the
beam direction. The apical view typically provides the best
window since the beams are then approximately aligned to
the longitudinal direction of the myocardium (except near
the apex).

«
...
162
163
164
165
166
...
»

Содержание Vivid S70






































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Vivid S70

Relion 670 series

Бренд: ABB Страницы: 66

Бренд: Makerfire Страницы: 10

Бренд: Navman Страницы: 17

Бренд: Taurus Страницы: 28

Бренд: Kärcher Страницы: 54

Бренд: ABB Страницы: 85

Бренд: Parker Страницы: 54

Бренд: Ecco Страницы: 2

Бренд: Landoll Страницы: 94

Бренд: Nektar Страницы: 3

Бренд: Youkey Страницы: 86

Бренд: Wacker Neuson Страницы: 62

Бренд: NEILPRYDE Страницы: 55

Бренд: HANYOUNGNUX Страницы: 4

Бренд: Park House Healthcare Страницы: 6

Бренд: J&M Страницы: 33

Бренд: iFIT Страницы: 11

Бренд: Madrigal Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды