GE GTW750CPLDG Скачать руководство пользователя страница 57 | Manualshive

Страница: 57 / 62

GE GTW750CPLDG Скачать руководство пользователя страница 57

– 57 –

2. Remove two 3/8 hex bolts securing the mode

shifter to the platform. The mode shifter,

FOXWFKFOXWFKVSULQJDQGÀDWZDVKHUZLOOSXOO

away from the platform.

Mode Shifter Reinstallation

1.

,QVWDOOWKHÀDWZDVKHURQWRWKHORZHU

transmission shaft.

2. Install the clutch spring.

3. Slide the clutch into the clutch level of the

mode shifter and slide the clutch onto the
shaft. There are guide pins on the bottom of
the mode shifter that go into locator holes on
the platform.

4. Install the two 3/8 hex bolts and torque to 60

in. pounds.

Locator Holes

Flat

Washer

Clutch

Spring

Clutch

Guide

Pins

Platform/Transmission Assembly

The platform assembly not only houses the
transmission, but is used to mount the drive
motor and mode shifter. The transmission has
planetary gears inside to assist with the agitation
and spin cycles of the washer. It is one complete
part with the exception of the two harness
mounting brackets (some models have one
harness mounting bracket) and a motor splash
guard.

Platform/Transmission Removal

1. Remove the impeller or agitator to access the

hub nut.

2. Remove the hub nut and Belleville washer.

The hub nut has reverse threads, and needs
to be turned clockwise to loosen.

3. Lean the washer back or lay the washer on its

side to access the bottom.

After all other components have been removed
from the platform assembly:

4. Cut the wire ties that support the main

harness to the platform assembly.

5. Remove the 3/8 hex bolts securing the

motor shield and the harness brackets to the
platform.

6. Remove the eight 3/8 hex bolts securing the

platform to the bottom of the tub.

7. Pry the platform assembly away from the tub.

(Continued next page)

«
...
55
56
57
58
59
...
»

Содержание GTW750CPLDG































































Отзывы:

Нет отзывов