GE GTW750CPLDG Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 62

GE GTW750CPLDG Скачать руководство пользователя страница 45

– 45 –

Dispenser Removal Continued

Using a pair of pinch pliers, clamp the tube so the

GHWHUJHQWGRHVQRWÀRZIURPWKHEXONWDQNLQWR
WKHGLVSHQVHUER[7KHWXEHLVSUHWW\ÀH[LEOHDQG

does not take much pressure to clamp it closed.

'UDLQKRVHDQGRUDLUFRQGLWLRQLQJSLQFKRႇSOLHUV

both work well.

NOTE

: Because the tank does not seal closed,

a sponge or Mr. Clean Magic Eraser can
be inserted into the tank opening to prevent
detergent for spilling out while servicing or
removing the washer from a drain pan.

If the tank is being removed or replaced, draining
the bulk tank is recommended.

1. Remove the fabric softener tray from the

dispenser body.

2. As shown earlier, remove the bleach funnel

to access and remove the 3/8 in. hex bolt that
helps to secure the bulk tank to the top cover.

3. Remove three 1/4 in. hex head screws

securing the dispenser body to the top cover.

Pry

Tab

Pull Here

Front

4. Raise the top cover to access the dispenser

box.

5.

8VLQJDÀDWEODGHVFUHZGULYHUSU\WKHWDE

at the bottom of the dispenser box out from

WKHPHWDOOLSRIWKHWRSFRYHU¿UVW

NOTE

: Be

careful not to pry too hard against the metal. It
can be bent. Also removing the dispenser box

¿UVWPDNHVLWHDVLHUWRJHWWKHEXONGHWHUJHQW

tank out.

6. Pull outward at the bottom of the box to

disengage the front of it from the top cover.

7. When the dispense box is reinstalled, the

IURQWRIWKHER[QHHGVWREHLQVHUWHG¿UVW

«
...
43
44
45
46
47
...
»

Содержание GTW750CPLDG































































Отзывы:

Нет отзывов