GE GTW750CPLDG Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 62

GE GTW750CPLDG Скачать руководство пользователя страница 42

– 42 –

The thermistor and harness comes as one
assembly that connects to the control board.
The thermistor also comes with an O-ring that
creates a water tight seal around the probe.
When reinstalling the thermistor, ensure that the
thermistor is seated properly. If it bulges, it will not
seal properly.

Thermistor

Bulging O-ring

Thermistor Resistance Table

Temp

(°C)

Temp

(°F)

5HVLVWDQFH

10

50

19901

15

59

15713

20

68

12493

28

82.4

8833

32

90

7446

38

100

5807

44

111

4558

50

122

3601

54

130

3108

66

150

2016

76

169

1435

Bleach/Bulk Tank Funnel

The bleach portion of the funnel directs the liquid
bleach to the top cover, dispensing it between the
outer tub and the basket. There is no water valve
to rinse the funnel after use. The bulk tank portion
of the funnel directs the liquid detergent into the
bulk tank.

Bleach/Bulk Tank Funnel Removal

1. To remove the bleach/bulk tank funnel, reach

between the top cover and tub cover and
push up on the bottom of the funnel.

2. Removing the funnel gives access to the bulk

tanks 3/8 in. mounting bolt.

3. To install the funnel onto the top cover, push

down on the funnel to seat it into position.

Bulk Tan

k

Mounting Bolt

«
...
40
41
42
43
44
...
»

Содержание GTW750CPLDG































































Отзывы:

Нет отзывов