GE GTW750CPLDG Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 62

GE GTW750CPLDG Скачать руководство пользователя страница 43

– 43 –

Dispenser Box

The dispenser box only has one drawer that
slides out. It is for the fabric softener. There
is no drawer for detergent.

DO NOT TRY TO

PULL THE WATER STATION SIDE OF THE
DISPENSER BOX OUT

. If the bulk tank is not

being utilized, detergent will need to be added
directly into the basket before adding clothing.

Dispenser Removal

To remove the dispenser; the backsplash, water

YDOYHDQGWRSFRYHUZLOOQHHGWREHUHPRYHG¿UVW

Before raising the top cover, if there is detergent
in the bulk tank, reach under the dispenser
box and feel for the rubber tube. Pull the tube
downwards to disengage it from the dispenser
box.

Dispensers

DOES NOT

OPEN

Fabric Softener

Tray

To support the top cover while servicing, this
method of support has proven to be helpful.

1. Tape the lid securely to the top cover. The lid

will come open while servicing if not taped in
place or removed.

2. Remove the two 1/4 in. hex head screws that

secures the backsplash assembly from the
top cover. Set these screws within reach as
they will be used in this application.

3. After removing the backsplash assembly,

remove the two 1/4 in. hex head screws at
the rear of the top cover that secures the top
cover to the cabinet.

4. Disengage the top cover from the front clips

that secures the top cover to the front of the
cabinet.

,03257$177RS&RYHU6XSSRUW:KLOH

6HUYLFLQJ

Existing Hole At Rear Of Top Cover

«
...
41
42
43
44
45
...
»

Содержание GTW750CPLDG































































Отзывы:

Нет отзывов