GE GTW750CPLDG Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 62

GE GTW750CPLDG Скачать руководство пользователя страница 38

– 38 –

After the lid is removed, the lid lever arms can be
slid out from the hinge assemblies. They are the
same, so they cannot be mixed up.

The hinges can be removed without removing the
top cover.

1. Slide the backsplash toward the rear of the

washer to access the hinge mounting screws.

2. Slide a hand between the top cover and the

tub cover and grasp the hinge being removed.

3. Remove two 1/4 in. hex head screws that

secure the hinge to the top cover and slide
the hinge out.

/LG+LQJH

Impeller

The impeller moves clothes around in the basket.
It takes the place of a tall agitator. Impellers
are designed to work best with moving material
around in the basket with low water levels.

Impeller Removal

1. Carefully remove the center cap from the

impeller. This can be done with a pocket
screwdriver or putty knife.

2. Remove the 7/16 hex bolt and slide the

LPSHOOHURႇRIWKHVKDIW7KHVSOLQHGFRXSOHULV

part of the impeller.

,PSRUWDQW

The impeller bolt (

Part #

:

WH02X24374) should be replaced any time it
is removed for service and torqued to 100 in.
pounds.

«
...
36
37
38
39
40
...
»

Содержание GTW750CPLDG































































Отзывы:

Нет отзывов