GE GTW750CPLDG Скачать руководство пользователя страница 23

Страница: 23 / 62

– 23 –

'LDJQRVWLFV

Consumer Error Mode (CEM)

Entry into Consumer Error Mode

Consumer Error Mode allows the consumer to
retrieve the fault codes to assist with diagnosis
at the time the consumer calls for service to their
machine. The consumer cannot delete any of the
codes or run any components.

)URPDQLGOHVWDWHDOO/('VRႇSUHVVDQG

hold the Start button for 10 seconds.

2. After holding Start for 10 seconds, all LEDs

will turn on signifying to the user to release
the Start button.

Behaviors While in Consumer Error Mode

The Pause and Lid Locked LEDs should be
constantly blinking while in CEM.

7KH¿UVWIDXOWLISUHVHQWZLOOVKRZRQWKH

display.

Pressing Start will display the next fault.

Models with a 7-segment display will
blink the fault number in the display.

At the end of the fault list or if no faults are
present:

Models with a 7-segment display will
display "- -".

([LWLQJ&RQVXPHU(UURU0RGH

Pressing any button (other than Start), or
turning any knob will exit the Consumer
Error Mode.

Consumer Error Mode will time out after 10
minutes.

Field Service Mode

Entry into Field Service Mode

)URPDQLGOHVWDWHDOO/('VRႇSUHVV

and hold the Start button for 10 seconds
while rotating the cycle selection knob 180
degrees (seven clicks) and then release the
Start button.

Once Field Service Mode is entered,

DOO/('VZLOOJRRႇIRUDSSUR[LPDWHO\

seconds, and then all will start blinking to
signify that Field Service Mode has been
entered.

7-segment display models (0) will be
displayed for Test 0.

Use the cycle selection knob to control the
test selection menu.

Rotating the knob clockwise will increment
the test numbers in the display.

Rotating the cycle select knob counter-
clockwise will decrement the test numbers
in the display.

Once the test number is selected, pressing
the Start button will begin the selected test.

Turning the cycle select knob while in a
selected test shall cancel that test and move
to the next test for selection.

([LWLQJ)LHOG6HUYLFH0RGH

Field Service Mode will time out after 30
minutes if there is no user activity.

On models with a 7-segment display, press
the Power button.

Содержание GTW750CPLDG































































Результаты поиска

Содержание GTW750CPLDG

Отзывы:

GE GTW750CPLDG, Техническое обслуживание руководство, Страница: 23 / 62

Результаты поиска

Содержание GTW750CPLDG

Отзывы: