GE GTW750CPLDG Скачать руководство пользователя страница 55

Страница: 55 / 62

– 55 –

Drive Motor

The drive motor is a 1/2 horsepower motor. They

DUHPRGHOVSHFL¿FDQGKDYHDVSHFL¿FGULYHEHOW

The drive belt letter color for this model is white.
This allows the machine to spin up to 800 RPM.

'ULYH0RWRUV'LDJQRVLQJ

The motor requires 120 VAC.

Resistance value from board connector J511 are:

1/2 horsepower motor

brown

white

and

brown

yellow

should read approximately

3.1 ohms.

Motor Removal

1. Unclip the hall sensor from the motor.

2. Unclip the main harness from the motor

connector by pushing down on the connector
clip. The clip is large enough that it can be
done with one hand. The motor side of the
harness is secured in place.

3. Remove the two 1/2 in. hex bolts that secures

the motor to the platform. When reinstalling
the bolts, torque to 170 in. pounds.

,PSRUWDQW

If removing the motor with the washer

leaning back, be sure to support the weight of the
motor, as it will drop away from the platform once
the second bolt is removed.

Содержание GTW750CPLDG































































Результаты поиска

Содержание GTW750CPLDG

Отзывы:

GE GTW750CPLDG, Техническое обслуживание руководство, Страница: 55 / 62

Результаты поиска

Содержание GTW750CPLDG

Отзывы: