GE GTW750CPLDG Скачать руководство пользователя страница 34

Страница: 34 / 62

– 34 –

Personality ID

Personality ID Numbers

To change the personality, the Service Mode must

EHHQWHUHG¿UVWVHHWKH

Entry into Field Service

Mode

section under

'LDJQRVWLFV

in this service

guide).

7-segment display models will display the number
programmed into the control.

1. Once Service Mode has been entered, rotate

the cycle knob to Test 17.

2. Press Start to enter the test.

3. The correct personality ID that has been

programmed into the control will be displayed.

4. If the personality is incorrect, press the Start

button again and the next valid personality will
be displayed.

5. When the desired personality is reached,

press and hold the Start button to select that
personality.

Personality Table

Model Number

Personality Number

MTW200**K0

HTW200**K0 & K1

HTW200**K2

HTW200**K3 & higher

GTW220**K0, K1 & K2

GTW220**K3

GTW220**K4 & higher

HTW240**K0 & K1

HTW240**K2

HTW240**K3 & higher

GTW330**K0 & K1

GTW330**K2

GTW330**K3 & higher

GTW460**J0 & J2

GTW460**J3, J4, J5 & J6

GTW460**J7

GTW460**J8 & higher

GTW485**J0 & J1

GTW485**J2 & J3

GTW485**J4 & higher

GTW490**J0 & J1

GTW490**J2 & higher

GTW680**J0, J1 & J2

GTW680**J3 & J4

GTW680**J5 & higher

GTW680**L0 & higher

GTW685**L0 & higher

GTW750**L0 & higher

Содержание GTW750CPLDG































































Результаты поиска

Содержание GTW750CPLDG

Отзывы:

GE GTW750CPLDG, Техническое обслуживание руководство, Страница: 34 / 62

Результаты поиска

Содержание GTW750CPLDG

Отзывы: