manualshive.com logo in svg

GE GTW750CPLDG, Техническое обслуживание руководство, Страница: 10 / 62

Поделиться
Скачать
GE GTW750CPLDG Скачать руководство пользователя страница 10

– 10 –

Items to Wash

Cycle

Wash 
Temp

Soil Level

Spin 

Selection

Options Available

Cycle Details

Cycle for 
normal, regular, 
or typical use 
for washing up 
to a full load of 
normally soiled 
cotton clothing.

Colors

Hot

Warm

Colors
Cool
Cold
Tap Cold

Ex. Heavy
Heavy

Normal

Light

Max
More

Normal

No Spin

Stain Removal 
Guide
Warm Rinse
Auto Soak
Deep Rinse
Delay Wash
Extra Rinse

Cycle for normal, regular or typical 
use for washing up to a full load 
of normally soiled cotton clothing. 
Choose the Heavy or Extra Heavy 
soil level selection and Warm or 
Hot water temperature selection 
as appropriate for the clothes load 
for a higher degree of cleaning. 

,QFRUSRUDWHVPXOWLVWDJH¿OOVDQG

wash periods to provide optimal 
fabric care.

Casual clothes, 
lightly soiled 

RႈFHZHDU

Casuals

Hot
Warm

Colors

Cool
Cold
Tap Cold

Ex. Heavy
Heavy

Normal

Light

Max
More

Normal

No Spin

Stain Removal 
Guide
Deep Fill
Warm Rinse
Auto Soak
Deep Rinse
Delay Wash
Extra Rinse

Wash cycle tailored to care for 

FDVXDOFORWKHVDQGRႈFHZHDU

items.

Lingerie and 
special care 
fabrics with 
light soil. 
Water-resistant, 
bedding and 
bulky items, 
such as large 
coats, mattress 
pads, and bath 
mats.

Delicates Hot

Warm
Colors
Cool

Cold

Tap Cold

Ex. Heavy
Heavy

Normal

Light

Max
More

Normal

No Spin

Stain Removal 
Guide
Deep Fill
Warm Rinse
Auto Soak
Deep Rinse
Delay Wash
Extra Rinse

Utilizes a unique "tri-pulse" extra 

JHQWOHDJLWDWHSUR¿OHWRSURYLGH

special care to delicate fabrics. It 
is recommended to place small or 
ultra-delicate items in mesh bags 
before washing.

Medium to 
lightly soiled 
athletic 
wear items 
of technical 
or synthetic 
fabrics.

Active-
wear

Hot

Warm

Colors
Cool
Cold
Tap Cold

Ex. Heavy
Heavy

Normal

Light

Max
More

Normal

No Spin

Stain Removal 
Guide
Deep Fill
Warm Rinse
Auto Soak
Deep Rinse
Delay Wash
Extra Rinse

Cycle designed for care of 
medium to lightly soiled active 
wear, athletic wear, and technical 
fabrics. Incorporates a dual 
stage wash period with soak to 

HႇHFWLYHO\WUHDWERG\VRLOVDQG

odors. Use the Heavy Duty cycle 
for heavily soiled sports clothing 
constructed of sturdy fabric.

Dark colored 
cottons, linens, 
and mixed 
loads.

Cold 
Wash

Hot
Warm
Colors
Cool
Cold

Tap 
Cold

Ex. Heavy
Heavy

Normal

Light

Max
More

Normal

No Spin

Stain Removal 
Guide
Deep Fill
Auto Soak
Deep Rinse
Delay Wash
Extra Rinse

Cycle combines multiple wash 
agitation periods with soak 
periods to provide enhanced 
cleaning performance and energy 

HႈFLHQF\ZLWKFROGHUZDWHU

temperatures.

D

Wash Cycles-Cycle Selector Knob

The wash cycle controls the type of washing process. The cycle selector knob can be turned 
in either direction. Turning the knob after starting a cycle will stop the washer and change the 
cycle options to the new selection. Press Start to begin the new cycle selection.
The chart below will help match the items to be washed with the best wash cycle settings. For 
optimal performance, select the cycle that most closely matches the items being washed.
Selections and options shown in bold are default settings for that cycle.
Some cycles and options may not be available on some models. 

Содержание GTW750CPLDG































































Отзывы:

Нет отзывов