GE GTW750CPLDG Скачать руководство пользователя страница 24

Страница: 24 / 62

– 24 –

([SODLQLQJ6HUYLFH0RGH7HVWV

7KHUHDUHGLႇHUHQWWHVWVWKDWFDQEHSHUIRUPHGRQWKHZDVKHUZKLOHLQ6HUYLFH0RGH

Once in the Service Mode, rotate the Cycle Select knob to advance to the desired test.

Knob Index /

Test number

Displayed on

VHJPHQW

display (SSD)

Test Name

Description of test

Turning the cycle knob will index to the next or prior test.

All LED’s on

All LEDs on the display will be blink including "88" at a rate of

1Hz.

Fault Codes

On Start button press, blink first fault code.

Display fault code in SSD.

At end of list OR if no fault codes are present, washer will flash

"- -".

Personality ID

Pressing Start will start the test.

Flash the set personality after pressing

Start

(See

Personality ID Numbers

, under

Personality ID

in the

'LDJQRVWLFV

section of this service guide for the correct ID for

the model being checked.)

UI Software

Version (Critical)

(Critical)

After entering

this test, press

the

Start

button

to toggle through

the software

version number

as follows:

After entering this test, press the Start button to toggle through

the software version number as follows:

Example

: v01.23

First press: "01" on 7SD

Second press: "23" on 7SD

UI Software

Version

(Non-critical)

After entering this test, press the Start button to toggle through

the software version number as follows:

Example

: v01.23

First press: "01" on SSD

Second press: "23" on SSD

XML Version

(Non-critical)

Example

: v01.23

First press: "01" on SSD

Second press: "23" on SSD

NOTE

: Only the non-critical version number is shown because

the critical XML version number must match the application non-

critical version number for the control to boot. If service mode is

attained, then the XML critical version is correct. If not, update

the software.

Hot Water Valve

Pressing Start will toggle the hot water valve on and off. Test will

have a time-out for how long valve will be on (1 minute). The

valve will turn off when the test is exited.

Cold Water Valve Pressing Start will toggle the cold water valve on and off. Test

will have a time-out for how long valve will be on (1 minute). The

valve will turn off when the test is exited.

Service Mode Tests

(Continued next page)

Содержание GTW750CPLDG































































Результаты поиска

Содержание GTW750CPLDG

Отзывы:

GE GTW750CPLDG, Техническое обслуживание руководство, Страница: 24 / 62

Результаты поиска

Содержание GTW750CPLDG

Отзывы: