GE GTW750CPLDG Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 62

GE GTW750CPLDG Скачать руководство пользователя страница 48

– 48 –

Load

Type

'HWHFWHG/RDG:HLJKW

0 to

5

lbs

5

to

lbs

to

lbs

to

lbs

to

lbs

lbs

Water Saver Rinse

*DOORQV

Wet

6

8

8

10

10

12

Synth

6

8

8

10

10

12

Mixed

6

8

8

10

10

12

Cotton

8

8

10

10

12

12

Water Levels

Approximate Minimum

:DVK:DWHU/HYHOV

Impeller Models

: 7 Gallons or 3 inches

deep from the bottom of the basket.

Approximate Maximum Wash Water Levels

:

Impeller Models

: 26 Gallons or 13-1/2 in.

deep from the bottom of the basket.

Press and hold the

Deep Fill

button for 3 seconds

to achieve.

 3UHFLVH)LOO6XSHU3OXV

:KHQSUHFLVH¿OO

is selected and a large absorbent load is
being washed, Super Plus water level is
invoked in the board software. Instead of
the normal 26 gallons of water, an additional
1 to 1.5 gallons will be added.

Impeller

Bulky

setting water level is 25 gallons or

12-3/4 in. deep from the bottom of the basket.

NOTE

: These levels are measured starting from

an empty tub.

Water Saver Rinse

The GTW750 model does not have a spray rinse.
A water saver rinse is used. So it is normal to
have water levels less than main wash water
levels.

7KHZDWHUVDYHUULQVHDOJRULWKPLVDVIROORZV

:

:DVKHU¿OOVIRUZDVKDQGFRPSOHWHVZDVK

agitation portion of the cycle like usual.

Washer drains wash water but does not
perform a wash spin. This is done for a few
reasons:

Some carryover wash water retained
in the clothing items allows for a higher
water level in the basket, working with
the water available for rinse while still
meeting government mandated water
usage requirements.

Clothing items are left in an orientation
which facilitates faster, lower water level
rinsing.

Addition of cycle time is prevented
through not spinning.

:DVKHUWKHQ¿OOVZLWKDTXDVLGHHS¿OOULQVH

called Water Saver Rinse.

Water level is lower than that of the

ZDVKZDWHUOHYHOEXWLVVWLOODGHHS¿OO

style rinse (as opposed to a spray rinse).

Washer then performs a brief period of rinse
agitation to move the fresh water through
the clothes.

Washer then pumps out rinse water and
completes the rinse spin portion of the cycle
as usual.

NOTE

: Users should still select “Deep Rinse” if

they are using liquid fabric softener.

«
...
46
47
48
49
50
...
»

Содержание GTW750CPLDG































































Отзывы:

Нет отзывов