GE GTW750CPLDG Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 62

GE GTW750CPLDG Скачать руководство пользователя страница 26

– 26 –

Knob Index /

Test number

Displayed on

VHJPHQW

display (SSD)

Test Name

Description of test

Turning the cycle knob will index to the next or prior test.

17

Change

Personality

Pressing Start will start the test.

Press Start button again and the next valid personality should be

displayed.

Press and hold the

Start

button to select the correct personality.

18

Analog Knob

Pressing Start will start the test.

Each options knob is represented by a specific corresponding

status LED. (Far left options knob to the far left status LED)

When knob position changes, the LED for the specific knob

blinks.

With each click to the right, the LED for the specific knob blinks

faster.

With each click to the left, the LED for the specific knob blinks

slower.

19

Bulk Detergent

Dispense Valve

Pressing Start will toggle the bulk valve on and off. Test will time

out after 1 minute turning the valve off.

«
...
24
25
26
27
28
...
»

Содержание GTW750CPLDG































































Отзывы:

Нет отзывов