manualshive.com logo in svg

GE GTW750CPLDG, Техническое обслуживание руководство, Страница: 53 / 62

Поделиться
Скачать
GE GTW750CPLDG Скачать руководство пользователя страница 53

– 53 –

The drive pulley is mounted to the drive motor. It 

KDV¿QVRQWKHPRWRUVLGHWRKHOSNHHSWKHPRWRU

cool during operation. 

The transmission pulley doubles as a gear for the 
mode shifter to lock into during agitation.

Pulley Removal

1.  Remove the two 9/16 nuts (one for each 

pulley), securing them to the motor and 
transmission shafts. 

2. 

6OLGHWKHSXOOH\VRႇWKHPRWRUDQG

transmission shafts. Torque the new pulley 
nut to 110 in. lb. when reinstalling.

The drive belt has six ribs and can be removed 
easily. To access the belt, the belt protector needs 

WREHUHPRYH¿UVW

Belt Protector Removal

1.  Remove three 3/8 hex head bolts securing the 

belt protector to the platform assembly and 
set the platform assembly aside.

Belt Removal

1.  Rotate the pulley by hand while walking the 

EHOWRႇRIWKHSXOOH\

Drive System

  Drive Belt

The drive system consists of the belt, pulleys, 
drive motor, mode shifter, speed/hall sensor and 
transmission. They all operate together to agitate 
and/or spin the load in the basket.

  Drive/Transmission Pulleys

Belt Installation

1.  Put the belt on the motor pulley.

2.  Stretch the belt around the transmission 

pulley as far as it will go.

3.  Rotate the pulley until the belt is centered on 

the transmission pulley. Ensure all of the belt 
ribs are properly located on the drive motor 
pulley.

Hex Head 

Bolt

Hex Head 

Bolt

Hex Head 

Bolt

Содержание GTW750CPLDG































































Отзывы:

Нет отзывов