manualshive.com logo in svg

GE GTW750CPLDG, Техническое обслуживание руководство, Страница: 15 / 62

Поделиться
Скачать
GE GTW750CPLDG Скачать руководство пользователя страница 15

– 15 –

I

Additional Options

0\&\FOH6HWWLQJV

As the cycle selector knob is turned, the Temp, Soil and Spin settings change to automatic 

SUHVHWGHIDXOWVHWWLQJVIRUHDFKF\FOH,IWKHXVHUGHVLUHVGLႇHUHQWGHIDXOWVHWWLQJVVHOHFWWKH

desired options or changes to the cycle settings, then press and hold the My Cycle button 
for 3 seconds to store them. The My Cycle button will light when active. In the future, when 
the user turns the selector knob to that cycle, the settings will be automatically recalled. To 
restore the factory defaults temporarily (i.e.: for this load), press the My Cycle button for 1/2 

DVHFRQG7KH0\&\FOHOLJKWZLOOWXUQRႇDQGWKHIDFWRU\GHIDXOWVZRZHYHUWKHQH[W

time the user selects this cycle, My Cycle settings will load. If the user wishes to permanently 
restore the factory default settings for the cycle; when the My Cycle is active (button light 
on) press and hold the My Cycle button for 3 seconds. The factory defaults will load for the 

VHOHFWHGF\FOHDQGWKH0\&\FOHOLJKWZLOOWXUQRႇ7KHGHIDXOWVHWWLQJVZLOOORDGZKHQWKLV
F\FOHLVVHOHFWHGLQWKHIXWXUHDQGWKH0\&\FOHOLJKWZLOOUHPDLQRႇ

NOTE

: My Cycle saves 

the following options: Temp, Soil, Spin, Extra Rinse, Deep Fill, Warm Rinse, Auto Soak and 
Deep Rinse.

Control Lock

Use the control lock before or during a cycle to prevent any selections from being made.
To lock/unlock the washer controls, press and hold the Warm Rinse and Auto Soak buttons 
for 3 seconds. The control lock icon will light up when it is on. 

NOTE

: The Power button can 

still be used when the machine is locked.

(Continued next page)

Содержание GTW750CPLDG































































Отзывы:

Нет отзывов