GE GTW750CPLDG Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 62

GE GTW750CPLDG Скачать руководство пользователя страница 41

– 41 –

Four Coil Water Valve Removal

1.

7XUQWKHKRXVHZDWHUVXSSO\RႇWRWKHZDVKHU

and disconnect power to the washer.

2. Remove the two 1/4 in. hex head screws

securing the backsplash to the top cover to
access the water valves.

3. Disconnect the harness from the valve.

4. Remove three 1/4 in. hex head screws

securing the valve to the top cover and pull
the valve up. The thermistor can now be
removed by prying up from under the metal
lip of the thermistor. Be sure the O-ring seal
comes out as well.

There are four replaceable rubber seals on the
water valve where it connects to the dispenser
box. They come with new valves, but can be
ordered separately (

Part #

: WH13X24094).

The water valve is located inside the backsplash
assembly.

$IRXUVROHQRLGYDOYHÀRZVLQWRDGHWHUJHQW

dispenser box.

The water valves are located and accessed from
inside the backsplash.

:DWHU9DOYH'LDJQRVLQJ

The four solenoid valve requires 120 VAC to
activate the coils. The resistance of the four coil
valve can be check from the J514 connector on
the control. They are approximately:

1374 ohms for cold and fabric softener

1515 ohms for hot and rinse

Water Valve

Fabric Softener

Bulk Detergent

Tap Cold

Cold

Hot

Rubber seals

Fill System

«
...
39
40
41
42
43
...
»

Содержание GTW750CPLDG































































Отзывы:

Нет отзывов