GE GTW750CPLDG Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 62

GE GTW750CPLDG Скачать руководство пользователя страница 16

– 16 –

J

SmartDispense™ (GTW750 model only)

When selected, this feature will automatically add detergent to the wash, eliminating the need to
add detergent for each load. The tank will hold approximately 75 ounces of liquid detergent. This

LVHQRXJKIRUDERXWDYHUDJHODXQGU\ORDGVZKHQ¿OOHGWRWKHPD[LPXPOHYHO

7KHGHWHUJHQWDPRXQWVHOHFWLRQRQWKHFRQWUROSDQHOZLOOGHIDXOWWR$872ZKHQ¿UVWSRZHULQJXS

the washing machine. When AUTO is selected, the amount of detergent needed for each laundry
load will automatically be determined based on the size of the load the machine senses.

If it is desired to manually select the amount of detergent for a given load, this can be done by
pressing the Detergent Dispense button on the control panel to select detergent for a Small, Nor-
mal or Large load. Small will provide less detergent than average, Normal will provide an aver-
age amount of detergent and Large will provide more detergent than average.

7KHVPDUWGLVSHQVHIHDWXUHFDQEHGLVDEOHGE\SUHVVLQJWKH'HWHUJHQW'LVSHQVHEXWWRQXQWLO2ႇ

is selected.

NOTE

: Not all cycles will allow the use of the SmartDispense feature. If the light is illuminated

EHORZWKH2ႇSRVLWLRQDQGSUHVVLQJWKH'HWHUJHQW'LVSHQVHEXWWRQUHVXOWVLQDEHHSLQJWRQH

then SmartDispense is not allowed for the cycle that has been selected. Detergent will need to
be added directly to the wash basket for these cycles.

This model does not have a dispenser drawer for detergent since it has a bulk detergent dispens-
ing system.

127(

If it is desired to manually add detergent for a load, that detergent will need to be added

directly to the basket, and the smart dispense set to OFF for that particular load.

127(

The right side of the dispensing area in the rear of the washer opening does NOT pull

RXW,WLVDVSRXWRQO\IRUZDWHUDQGGHWHUJHQWWRÀRZIURPWKHVPDUWGLVSHQVHV\VWHP

127(

,ILWLVGHVLUHGWRFKDQJHGHWHUJHQWW\SHLQWKHGHWHUJHQWWDQNLWLVQRWUHTXLUHGWRÀXVKWKH

VPDUWGLVSHQVHV\VWHP7KHQHZGHWHUJHQWW\SHFDQEHDGGHGWRDSDUWLDOO\¿OOHGWDQNKRZHYHU

it will not be immediately dispensed until the original detergent is completely dispensed from the
system.

127(

In the event that excessive chlorine bleach is accidentally spilled or otherwise gets into

the detergent tank, please follow the Detergent Tank Clean-Out instructions in the Care and
Cleaning section in order to minimize the possibility for clothing damage. If only a few drops of

EOHDFKDUHVSLOOHGLQWRWKHGHWHUJHQWWDQNWKHUHLVQRQHHGWRÀXVKWKHWDQN

Bulk Dispensing

Spout Only

DO NOT PULL

(Continued next page)

«
...
14
15
16
17
18
...
»

Содержание GTW750CPLDG































































Отзывы:

Нет отзывов