manualshive.com logo in svg

GE GTW750CPLDG, Техническое обслуживание руководство, Страница: 11 / 62

Поделиться
Скачать
GE GTW750CPLDG Скачать руководство пользователя страница 11

– 11 –

(Continued next page)

Items to Wash

Cycle

Wash 
Temp

Soil Level

Spin 

Selection

Options Available

Cycle Details

Small loads of 
lightly soiled 
items that are 
needed in a 
hurry. Examples 
include one 
casual wear 

RXW¿WRU

three soccer 
uniforms.

Speed 
Wash

Hot

Warm

Colors
Cool
Cold
Tap Cold

Ex. Heavy
Heavy

Normal

Light

Max
More

Normal

No Spin

Stain Removal 
Guide
Deep Fill
Warm Rinse
Auto Soak
Deep Rinse
Delay Wash
Extra Rinse

Utilizes more intense agitation 

SUR¿OHH[SHGLWHGZDVKSHULRG

and time saving continuous spray 
rinse to clean small lightly soiled 
loads in the fastest time possible.

Wet load of 
items. For items 
that need only 
to be rinsed, 
use this cycle 
with the Deep 
Rinse option.

Drain & 
Spin

Max
More

Normal

No Spin

Deep Rinse
Extra Rinse

Utilizes a high speed spin to 
extract water from wet items. 

For 

items that need to be rinsed, 
select the Deep Rinse option 

ZKHQXVLQJWKLVF\FOH

Cleaning 
the basket 
of residue 
and odor. No 
clothes to be 
washed using 
this cycle.

Basket 
Clean

Hot

([

Heavy

 

Normal

Deep Fill
Deep Rinse

Recommended use of at least 
once per month. Never load 
laundry when using this cycle, 
laundry may become damaged or 
contaminated. Cycle incorporates 
a hot deep wash, intense
agitation action, a dispenser 
purge (on some models), and a 
deep rinse.

Heavily soiled 
colorfast items.

Sanitize 
with Oxi*

Hot 

([

Heavy

 

Max

More

Warm Rinse
Auto Soak
Deep Rinse
Delay Wash
Extra Rinse

Cycle uses an initial lower water 

¿OOIRUVXSHUFRQFHQWUDWHG

high temperature sanitization 
followed by a heavy wash 
step. A pump purge and deep 
rinse is incorporated to remove 
contaminants. See additional 

GHWDLOVDQGFHUWL¿FDWLRQVLQWKH

Sanitize With Oxi

 section. Smart 

Dispense not available on this 
cycle.

Jeans with 
medium to light 
soil. For heavily 
soiled work 
jeans, use the 
Heavy Duty 
Cycle.

Jeans

Hot
Warm
Colors
Cool

Cold

Tap Cold

Ex. Heavy
Heavy

Normal

Light

Max
More

Normal

No Spin

Stain Removal 
Guide
Deep Fill
Warm Rinse
Auto Soak
Deep Rinse
Delay Wash
Extra Rinse

Combines higher water levels 
a, specially designed agitation 

SUR¿OHDQGPXOWLVWHSZDVKDQG

soak periods to care for jeans 
with medium to light soil. Use 
the Heavy Duty cycle for heavily 
soiled work jeans.

Sturdy fabrics 
with heavy to 
medium soil.

Heavy
Duty

Hot

Warm

Colors
Cool
Cold
Tap Cold

Ex. Heavy

Heavy

Normal
Light

Max
More

Normal

No Spin

Stain Removal 
Guide
Deep Fill
Warm Rinse
Auto Soak
Deep Rinse
Delay Wash
Extra Rinse

Incorporates multi-step wash 
and soak periods combined 
with extended wash periods 

WRHႇHFWLYHO\FOHDQKHDYLO\WR

medium soiled sturdy fabrics.

D

Wash Cycles-Cycle Selector Knob - Continued

Содержание GTW750CPLDG































































Отзывы:

Нет отзывов