manualshive.com logo in svg

GE GTW750CPLDG, Техническое обслуживание руководство, Страница: 35 / 62

Поделиться
Скачать
GE GTW750CPLDG Скачать руководство пользователя страница 35

– 35 –

Before removing the backsplash assembly, be 
sure to protect the lid and top cover with a towel 
or material to keep the lid from being damaged.

1.  Remove the two 1/4 in. hex head screws that 

secure the backsplash to the top cover.

2.  Grasp the backsplash sides, push it back. 

Then rotate it toward the rear of the washer 
so that the pressure tube can be seen and 
disconnected from the pressure sensor, 
mounted on the control board.

3.  Carefully disconnect the pressure tube from 

the control board. Twisting the pressure tube 

ZKLOHSXOOLQJZLOOKHOSLWVOLSRႇRIWKHSUHVVXUH

sensor.

4.  Rotate the backsplash assembly forward and 

carefully lay it face down.

5.  Remove the four 1/4 in. hex head screws that 

secure the rear cover to the backsplash, and 

OLIWLWRႇFDUHIXOO\7KHUHLVDJURXQGZLUHDQG

the RJ45 connector connected to the rear 
cover that will need to be disconnected.

6.  Disconnect the RJ45 connector by pressing 

down on the release tab and push through the 
opening. 

When reinstalling the RJ45, the stationary lip 
of the connector needs to be inserted into the 

RSHQLQJ¿UVW

NOTE

: Be sure to reconnect and test all ground 

wires.

Backsplash 

Screws

Pressure Sensor Tube

Capacitor

Pressure 

Sensor 

Tube

Four 1/4 in. 

hex head 

screws

RJ45     

Connector

Cabinet and Structure

Содержание GTW750CPLDG































































Отзывы:

Нет отзывов