manualshive.com logo in svg

GE GTW750CPLDG, Техническое обслуживание руководство, Страница: 14 / 62

Поделиться
Скачать
GE GTW750CPLDG Скачать руководство пользователя страница 14

– 14 –

(Continued next page)

6HWWLQJV

Individual settings for agitation (Soil), water temperature (Temp), and spin (Spin) can be set 
from the minimum (lowest in column) to maximum (highest in column). In general, the higher 
up the column, the more washer energy will be used.

127(

 Longer spin times typically reduce dryer time/energy usage (i.e.: reduces total 

energy when using both a washer and a dryer).

Cycle Options
Deep Fill 

Select the Deep Fill feature for loads where extra water is needed. The Deep Fill feature is 
recommended for special caseloads only, not for typical use. 
Press the Deep Fill button once before starting the cycle to add an incremental amount of 
water to the wash load. Holding the Deep Fill button for 3 seconds will provide the deepest 

¿OOOHYHOSRVVLEOHWKLVZLOOLQFUHDVHF\FOHWLPHGXHWRWKHDGGLWLRQDOWLPHLWWDNHVWR¿OOWKH

washer.
 
To cancel the option if desired, press the Deep Fill button again. 

127(

 The 

'HHS)LOOEXWWRQFDQDOVREHSUHVVHGDIWHUWKHZDVKHUKDVFRPSOHWHG¿OOLQJDQG

LVLQWKHZDVKSKDVHLIDGGLWLRQDOZDWHULVGHVLUHG7RVWRSWKHH[WUD¿OOSUHVVWKH

Deep Fill 

button again and the water will stop. 

Warm Rinse

 

3URYLGHVDZDUPULQVHWRWKHZDVKORDG1RWHWKDWULQVLQJRSHUDWLRQVPD\EHGLႇHUHQWZLWK
WKLVRSHUDWLRQVHOHFWHGLQRUGHUWRHႇHFWLYHO\DSSO\WKHZDUPULQVHZDWHUWRWKHORDG

Auto Soak

 

7KLVRSWLRQEHJLQVZLWKDEULHIDJLWDWLRQVRDNVIRUDVSHFL¿HGSHULRGRIWLPHWKHQPRYHV

through the rest of the cycle automatically. Repeated pressing of the Soak button will scroll 
through 15 minute, 30 minute, 1 hour and 2 hour selections and then return back to 0 soak 
minutes. 

Deep Rinse 

Set this option to provide a deep rinse or when using fabric softener. It may change other 
settings (e.g.: Spin may go to a higher setting) to maximize performance. 

Delay Wash 

When the Delay Wash button is repeatedly pressed, the delay time is set from 1 (01H) to 
9 (09H) hours and back to clear (00H) hours. Press and hold the Delay Wash button for 3 
seconds to immediately reset. 

Extra Rinse 

When using extra detergent or bleach to clean heavily soiled clothes, use the Extra Rinse 
option to better remove additional residues. 

NOTE

: This option is not allowed for some 

cycles.

G

H

Содержание GTW750CPLDG































































Отзывы:

Нет отзывов