GE GTW750CPLDG Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 62

GE GTW750CPLDG Скачать руководство пользователя страница 50

– 50 –

3. Disconnect the harness connector for the

recirculation pump.

4. Disconnect the wire tie securing the harness

to the platform assembly. A new wire tie
comes attached to the drain pump harness.

5. Remove three 3/8 hex head bolts securing the

pump to the tub.

6. Pull the pump away from the tub. Be sure the

VHDOFRPHVRႇZLWKWKHSXPS

The seal comes with a new pump but can be
ordered separately.

The recirculation pump is located on the bottom
front of the tub and is mounted directly to the
bottom of the tub. The recirculation pump is a
120 VAC pump used to recirculate water from the
tub assembly, up through a tube to the top of the
basket. The recirculation pump utilizes the tub
cover to spray water over the clothes.

Recirculation Pump

'LDJQRVWLFV

1. Disconnect power to the washer and access

the control board.

2. Disconnect the J512 connector from the

board.

3. Check resistance from pin 1 (

brown

wire) to

pin 6 (

red

wire). The resistance should read

approximately 31.7 ohms. If the resistance is
within range, ensure that the pump has 120
VAC at the pump harness connector.

Recirculation Pump and Tube Removal

Before removing the drain or recirculation pump,
any water in the basket must be removed. If the
drain pump is inoperable, water can be removed
by using a transfer pump shown on the following
page.

Lean the washer back using ergo-assisting prop
blocks or lay the washer on its side to access the
bottom of the tub.

1. Disconnect the recirculation tube from the

recirculation pump.

2. Pull downward on the tube to disengage it

from the tub.

Pump Seal

Recirculation Pump

Wash System

«
...
48
49
50
51
52
...
»

Содержание GTW750CPLDG































































Отзывы:

Нет отзывов