Gambro AK 98 Скачать руководство пользователя | Manualshive

Страница: 185 / 386

background image

HCEN12745 Revision 10.2016
Program version 2.xx

AK 98 Dialysis Machine - Technical data and specifications

A:183

Aproximate time
Rinse/Drain

10 minutes

Aproximate time Drain 4 minutes

14.1.15

Disinfection and cleaning – exterior cleaning

All outside parts of the machine can be cleaned with ethanol (70 %) or isopropanol (60
%).

14.1.16

Water supply

WARNING!

To ensure the quality of the dialysis fluid, inlet water quality shall comply with
appropriate regulations and as a minimum requirement according to ISO 13959.
The table below is presenting the requirements for the water supply required for the
AK 98 dialysis machine.

AK 98 dialysis
machine water
consumption

During treatment: maximum 770 mL/min

During disinfection: 800 mL/min with peaks of 1100 mL/min not
exceeding 40 seconds.

Minimum inlet
pressure

0.12 MPa (1.2 bar)

Maximum inlet
pressure

0.6 MPa (6 bar)

Inlet temperature

Treatment: +5 to +30 ºC
Disinfection: +5 to +90 ºC

Connector in/outlet

Diameter 8 mm

Quality

Inlet water quality shall comply with appropriate regulations and as a
minimum requirement according to ISO 13959.
Level for conductivity shall not exceed 0.1mS/cm. It is possible to use
water with higher conductivity if it consists mainly of sodium salts. This
may however affect the accuracy of the fluid composition.

NOTE!

Local regulations may require the use of separation devices
in the supply and special measures to protect against the
possibility of back-syphonage from dialysis equipment into
the water supply.

Drain

The drain tube outlet shall be placed between floor level and maximum
1.2 m above the outlet connection from the fluid monitor. An air gap to
atmospheric pressure must always be arranged at the tube outlet.

Length of drain tube

≤10 m

14.1.17

Power supply

Mains voltage

115 V AC, 50 Hz
115 V AC, 60 Hz
230 V AC, 50 Hz
230 V AC, 60 Hz

Protection class

Machine: Class 1 type B

BPM: Type BF

«
...
183
184
185
186
187
...
»

Содержание AK 98



































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AK 98

Бренд: dbx Страницы: 2

Бренд: Eagle Group Страницы: 8

Бренд: G-Lab Страницы: 16

Бренд: G&G Страницы: 2

Бренд: Jasco Страницы: 2

Бренд: MacDon Страницы: 2

Бренд: H&S Страницы: 54

Бренд: Samson Страницы: 2

Бренд: StarDental Страницы: 2

Бренд: USC Страницы: 29

Бренд: IDENTITES Страницы: 3

Бренд: Vahle Страницы: 6

Бренд: Coopers of Stortford Страницы: 3

Бренд: OttLite Страницы: 2

Бренд: Rohde & Schwarz Страницы: 36

MicroVention MCS-18

Бренд: Terumo Страницы: 104

Бренд: Leica Страницы: 270

Бренд: FISBA Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды