Gambro AK 98 Скачать руководство пользователя | Manualshive

Страница: 12 / 386

background image

A:10

AK 98 Dialysis Machine - Before you get started

HCEN12745 Revision 10.2016

Program version 2.xx

1.1

Important while reading the operator’s manual

1.1.1

About this operator´s manual

This operator’s manual provides instructions necessary for the proper operation of the
AK 98 dialysis machine. It is not a guide for the administration of haemodialysis.

1.1.2

Safety definitions

Warning

WARNING!

A warning alerts the reader about a situation which, if not avoided, could result in an
adverse reaction, injury or death.

Caution

CAUTION!

A caution alerts the reader about a situation which, if not avoided, could result in
minor or moderate injury to the user or patient or damage to the equipment or other
property.

Note

NOTE!

Notes are added to give more information.

1.1.3

Values and settings

Parameter values are set by the operator. For example treatment time and some alarm
limits. See Section 1.1.5

“About the screen”

on page A:11. All values and settings in

this operator’s manual are default values, which are set when the dialysis machine is
manufactured. Check with the authorised service technician responsible for installing
the dialysis machine if there are any values that are changed from the default settings.

Preset

When this symbol

appears in the manual text, it indicates the possibility to preset

the value of a parameter. Such a preset is done to adapt the settings of the machine to
correspond with the routines of the user/clinic or specific patient prescription. A preset
change shall always be done by an authorised service technician. For example, it is
possible to preset the machine for which mode to start up in, some alarm limits, some
functions and options. An authorised service technician shall, together with the user,
confirm that the presets have been properly set.

1.1.4

Buttons

The buttons on the operator's panel, to the right of the screen, light up in different
situations to guide the operator or to inform of actual status. See Figure 1-1

operator´s panel”

on page A:11. The illustrations in the handling instructions do not

normally show if the button is lit or unlit; the button figures are the same for lit, flashing
and unlit buttons.

The buttons on the screen can be lit, disabled or flashing depending on the status and
action but in this manual this state of the button is not reflected in the text or picture.

«
...
10
11
12
13
14
...
»

Содержание AK 98



































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AK 98

Бренд: NEC Страницы: 44

Бренд: Paia Страницы: 11

Бренд: CAB Страницы: 39

Бренд: CAB Страницы: 27

Бренд: Olsen Страницы: 4

Dominator Series

Бренд: Falcon Страницы: 31

Бренд: Fakir Страницы: 22

Бренд: Pahlen Страницы: 20

Бренд: Paia Страницы: 7

Бренд: Mac Medical Страницы: 23

MS-1 MICRO SEQUENCER - MUSICIAN S GUIDE

Бренд: Kurzweil Страницы: 91

Бренд: schmersal Страницы: 20

Бренд: Bodyworx Страницы: 17

Бренд: Wood-mizer Страницы: 59

Бренд: Tandem Страницы: 7

MERLIN N Series

Бренд: Meheen Страницы: 24

Бренд: Williams Sound Страницы: 32

LIGHT LINEAR PT 1

Бренд: LIGMAN Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды