background image

 

Installing a NetIron MLX Series Router

December 2008

© 2008 Foundry Networks, Inc.

3-51

Connect the other end of the cables to the DC power source. Repeat this step for each installed DC power 
supply. Then switch on the power source.

3.

If your power source is AC, attach one end of a Foundry-supplied AC power cord to the AC power supply as 
described in the appropriate section:

“Connecting AC Power to a NetIron MLX-4 Chassis” on page 3-9

“Connecting AC Power to a NetIron MLX-8 Chassis” on page 3-17

“Connecting AC Power to a NetIron MLX-16 Chassis” on page 3-26

“Connecting AC Power to a NetIron MLX-32 Chassis” on page 3-46

Insert the other end into a 115V/120V wall outlet. Repeat this step for each installed AC power supply.

WARNING:

 If the installation requires a different power cord than the one supplied with the device, make 

sure you use a power cord displaying the mark of the safety agency that defines the regulations for power 
cords in your country. The mark is your assurance that the power cord can be used safely with the device.

NOTE:

The NetIron MLX Series router is designed to provide uninterrupted service even when you insert or 

remove the management modules and the interface modules. Therefore, the system does not have a 
separate on/off power switch. To turn the system off, simply unplug the power cord(s).

NOTE:

The wall outlet should be installed near the equipment and should be easily accessible.

4.

Verify that the NetIron MLX Series router has initialized successfully. For information, see “Verifying Proper 
Operation”be
low.

Verifying Proper Operation

To verify the proper operation of the NetIron MLX Series chassis after power on, you can do the following:

Observe the LEDs

Display the status of the modules using the CLI

Observing the LEDs

After a NetIron MLX Series chassis powers on, you can observe its LEDs to verify that it initialized successfully. 
Table 3.5 outlines the LEDs, the desired state of each LED, possible abnormal states of each LED, and what to do 
if an LED indicates an abnormal state.

Table 3.5: Desired and Abnormal LED States After System Power On 

LED

Desired State

Meaning

Abnormal 
State

Meaning/Action

Management Module 

Active

The Active LED on 
one of the installed 
management 
modules should be 
on.

The module is 
functioning as the 
active management 
module.

Off

Neither of the management 
module(s) is managing the switch 
fabric and interface modules.

A problem could have occurred 
during initialization. Check your 
attached PC or terminal for 
possible error messages.

Содержание NetIron MLX-16





























































































































































































































Отзывы: