Fischer Panda Panda 12 mini PMS Digital Скачать руководство пользователя страница 96

Страница: 96 / 106

Tables

Page IV Panda_12mini_PMS_Digital_s00865_Installation manual.V02 - Chapter E: Tables

23.1.07

MOTOR RUNS IN OFF POSITION

Cause

Solution

Fuel inlet solenoid valve or throttle shut solenoid is not
switching off.

Check wire connections to solenoid. Check valve
functions as in the "Inlet Fuel Solenoid Valve" or in the
trottle shut off solenoid sections. Replace if necessary.

MOTOR STOPS BY ITSELF

Cause

Solution

Lack of fuel.

Check fuel supply system.

Excess heat in cooling system (thermo switch tripped)-
lack of cooling water. Is indicated on the remote control
panel.

Check cooling water system flow: water pump, inlet
water filter, extra heat exchanger coolant flow.

Lack of oil (oil pressure sensor tripped). Is indicated on
the remote control panel.

Check oil-level and if necessary top up.

Check motor's oil-pressure and have repaired by
Kubota-Service if necessary.

SOOTY, BLACK EXHAUST

Cause

Solution

Generator is overloaded.

Check electrical load and switch off unnecessary load.

Insufficient intake air.

Check intake air filter; clean if necessary.

Fuel injector faulty.

Replace injector.

Valve clearance incorrect.

Readjust valve clearance to correct value (refer to
Kubota-manual).

Poor fuel quality.

Use better quality diesel (recommended: 2-D Diesel).

Poor combustion.

Incorrect AFR (air/fuel ratio) due to motor timing adjust-
ment. Have motor serviced by Kubota.

GENERATOR MUST BE SHUT OFF IMMEDIATELY IF:

Cause

Solution

- motor rpm suddenly rises or drops

- unusual noise comes from genset

- exhaust colour suddenly becomes dark

- leakage in the cooling water system.

Refer to respective section of manual and if necessary,
have repaired by Kubota-Service, or Panda represen-
tative.

Содержание Panda 12 mini PMS Digital











































































































Результаты поиска

Содержание Panda 12 mini PMS Digital

Отзывы:

Fischer Panda Panda 12 mini PMS Digital, Руководство по установке, Страница: 96 / 106

Результаты поиска

Содержание Panda 12 mini PMS Digital

Отзывы: