Fischer Panda Panda 12 mini PMS Digital Скачать руководство пользователя страница 94 | Manualshive

Страница: 94 / 106

Fischer Panda Panda 12 mini PMS Digital Скачать руководство пользователя страница 94

Tables

Page II Panda_12mini_PMS_Digital_s00865_Installation manual.V02 - Chapter E: Tables

23.1.07

DIESEL MOTOR FAILS TO START

Cause

Solution

Starter battery switched "OFF".

Check position of battery switch and switch "ON" (if
installed).

Starter battery voltage insufficient (battery too weak).

Inspect battery terminals and cables for a good electri-
cal connection (Inspect against corrosion, tattered
wires, etc.).

Starting current disrupted.

During the normal starting process, the battery voltage
drops to 11V with a fully charged battery. If the voltage
does not drop during starting, the electrical connection
is faulty. If the battery voltage drops lower than 11V,
then the battery has been discharged.

STARTER IS TURNING MOTOR, BUT FAILS TO START

Cause

Solution

Fuel inlet solenoid valve not opening.

Check wire connections and circuitry to solenoid valve.
(ref. DC wiring diagram)

Fuel pump not working.

Check fuel-filter and pump: clean if necessary.

Lack of fuel.

Check fuel supply.

Glow-plugs not working correctly.

Check glow plugs and heating time.

Too much air in fuel lines.

Test fuel system for leakage. Bleed air from fuel
system (refer to section "Bleeding Air from Fuel
System").

Fuel-filter blocked.

Replace fuel filter.

MOTOR DOES ACHIEVE ENOUGH SPEED DURING STARTING PROCESS

Cause

Solution

Starter battery voltage insufficient.

Check battery.

«
...
92
93
94
95
96
...
»

Содержание Panda 12 mini PMS Digital











































































































Отзывы:

Нет отзывов