Festo Soft Stop SPC11 Series Скачать руководство пользователя страница 74 | Manualshive

Страница: 74 / 134

background image

4. Commissioning

4-14

Festo P.BE-SPC11-SYS-ASI-EN en 0203NH

4.3

Procedure for commissioning

Warning

Faults in the system structure and incorrect parameters
can cause the slide to move to an end position uncu-
shioned. The fixed stop or the drive may then be damaged.
You must observe the following instructions in order to
prevent such collisions.

– The SPC11 “learns” the location of the end positions

(cylinder end positions or fixed stop positions) by means
of the teach procedure. The teach procedure must be
carried out:

– with the first commissioning

– when the fixed stops have been adjusted

– when components and tubing have been replaced

– when parameters (A, C, S) have been modified.

– During the teach procedure the SPC-11 can recognize

faulty drive tubing or incorrectly set parameters. The
teach process must therefore be carried out again if the
tubing is disconnected and then reconnected, or if the
existing settings are modified.

– Make sure that the maximum permitted mass load is

observed during operation.

Recommendation: Place appropriate warning signs on your
system.

«
...
72
73
74
75
76
...
»

Содержание Soft Stop SPC11 Series







































































































































Отзывы:

Нет отзывов

Похожие инструкции для Soft Stop SPC11 Series

Бренд: Wavetec Страницы: 17

Бренд: Calsense Страницы: 9

Smart Controller

Бренд: MaestroHome Страницы: 10

Бренд: Kasco Страницы: 3

Бренд: Samson Страницы: 52

Бренд: Samson Страницы: 32

Бренд: Danfoss Страницы: 59

Бренд: Danfoss Страницы: 37

Бренд: Daikin Страницы: 44

Бренд: Eaton Страницы: 6

Бренд: Eaton Страницы: 35

Бренд: Eaton Страницы: 18

Бренд: Eaton Страницы: 73

Бренд: Eaton Страницы: 4

Cutler-Hammer IQ DP-4000

Бренд: Eaton Страницы: 87

Бренд: Eaton Страницы: 14

Бренд: Eaton Страницы: 36

Бренд: Salda Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды