Festo Soft Stop SPC11 Series Скачать руководство пользователя страница 78 | Manualshive

Страница: 78 / 134

background image

4. Commissioning

4-18

Festo P.BE-SPC11-SYS-ASI-EN en 0203NH

Caution

During the teach procedure, the moveable mass moves at
first slowly, then at the highest possible acceleration and
speed. Make sure that:
– nobody can place his/her hand in the positioning range

of the moveable mass, unless the compressed air supply
is switched off.

– the complete positioning range is free of any objects.

4. If teaching has not yet taken place, the SPC11 indicates

readiness to carry out the teach procedure (t flashes).

(The t flashes.)

Then proceed as described under 5.

If teaching has already taken place, the moveable mass
stands closed-loop controlled in a taught position
(P.01...P.04) or in any (P...) position. Proceed as follows:

S

Hold the Enter/Teach button pressed down for at least
2 seconds. The SPC11 then indicates readiness to
carry out the teach procedure (t flashes).

5. Hold the Enter/Teach button down at least 2 seconds in

order to start the teach procedure.
The SPC11 then carries out the teach procedure. The
moveable mass moves at first slowly, then dynamically.
The display shows the following:

The dots flash at the same rate

The teach procedure can last several minutes, depending on
the drive used. It is concluded when the drive is at end posi-
tion P.01. The display shows the following:

«
...
76
77
78
79
80
...
»

Содержание Soft Stop SPC11 Series







































































































































Отзывы:

Нет отзывов

Похожие инструкции для Soft Stop SPC11 Series

Бренд: J4C Страницы: 4

Бренд: ABB Страницы: 6

Relion 670 series

Бренд: ABB Страницы: 760

Бренд: ABB Страницы: 128

Бренд: Samson Страницы: 100

Бренд: Radio Shack Страницы: 3

Бренд: Haier Страницы: 58

Бренд: Barthelme Страницы: 8

Бренд: CAB Страницы: 28

Бренд: C-TEC Страницы: 16

Бренд: C&T Solution Страницы: 27

SECURIT ST800L+

Бренд: C&K systems Страницы: 16

Бренд: Haldex Страницы: 8

Бренд: Parker Страницы: 30

Compax3M Series

Бренд: Parker Страницы: 52

Бренд: Parker Страницы: 337

Бренд: Xilinx Страницы: 2

Бренд: ABB Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды