manualshive.com logo in svg

Festo Soft Stop SPC11 Series, Системное руководство

Поделиться
Скачать
Festo Soft Stop SPC11 Series Скачать руководство пользователя страница 84

4. Commissioning

4-24

Festo P.BE-SPC11-SYS-ASI-EN en 0203NH

Overview: Teaching the intermediate positions

Order

type?

The mass stands in position

e.g. P.01; O... supplies a 1-signal

P.03 and P.04 can be

taught.

Move manually
in order to teach

positions 3...4

{

or

}

Teach P.01...02 again:

Teach button/input

The SPC11 waits for

the teach task.

Positioning task via

inputs I1...I4

The mass moves into

the desired position.

Teach mode for positions

3...4 active (e.g. P.03).

The mass moves in the

desired direction.

Save the

position?

Yes
Enter/Teach

No

ESC

The mass now

stands closed-loop

controlled in the

current position.

The position is saved.

The mass stands

closed-loop controlled,

e.g. P.03; O... supplies

a 1-signal.

Position number

flashes

See at

1

See at

1

1

The dots flash.

The dots flash.

The t flashes.

The teach procedure

will be carried out

again.

Start:

Enter/Teach

Fig. 4/4: Teaching the intermediate positions (P.03 and P.04)

Содержание Soft Stop SPC11 Series







































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды