manualshive.com logo in svg

Festo Soft Stop SPC11 Series, Системное руководство

Поделиться
Скачать
Festo Soft Stop SPC11 Series Скачать руководство пользователя страница 71

4. Commissioning

4-11

Festo P.BE-SPC11-SYS-ASI-EN en 0203NH

4.2.1 Modifying parameters

If necessary, the set parameters can be modified, e.g. in order
to correct entry errors or to optimize positioning behaviour.
This can be carried out in one of the following ways:

Possibilities

Description

Activate
modification mode

In this mode the set parameter values are
retained and can be modified or trans-
ferred. Taught intermediate positions are
retained.

Create status as at
delivery

All parameter values are then set to 0.
Taught intermediate positions are deleted.

Activate modification mode

Prerequisites:

The measuring system must be connected. The yellow AS-
Interface bus cable must

not

be connected, as otherwise the

button functions of the SPC11 cannot be used. The drive
must be at a stand.

Caution

When the modification mode is activated the valve slide
assumes the mechanical intermediate position. During
positioning the mass can move uncushioned into an end
position.
Make sure that the drive is standing still before you acti-
vate the modification mode.

Use the buttons as follows to activate the modification mode:

1. Make sure that the drive is standing still.

2. Press all three buttons on the SPC11 at the same time.

Содержание Soft Stop SPC11 Series







































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды