manualshive.com logo in svg

Festo Soft Stop SPC11 Series, Системное руководство

Поделиться
Скачать
Festo Soft Stop SPC11 Series Скачать руководство пользователя страница 92

4. Commissioning

4-32

Festo P.BE-SPC11-SYS-ASI-EN en 0203NH

4.4.3 Controlling the SPC11

The SPC11 can be operated as an AS-Interface standard slave
with 4-bit I/O data and in accordance with slave profile 7.4
(multibit data). Depending on the AS-Interface profile used,
the following functions can be accessed via the AS-Interface:

Supported functions via the AS-Interface

Standard slave
with 4-bit I/O
data

Slave profile
7.4

Operating functions
– Move to the 4 taught positions
– Feed back when the taught positions are reached
– Load new intermediate position
– Read out the actual position

?
?

-
-

?
?
?
?

Diagnostic functions
– Read out the firmware and version numbers
– Read out the actual position
– Read out the ID string
– Check the status (parameters OK, position taught)
– Quit faults

-
-
-
-
-

?
?
?
?
?

Commissioning functions
– Load and read out parameters
– Start the teach procedure
– Move the drive manually (move left/right)
– Accept the actual position as the intermediate position

-
-
-
-

?
?
?
?

Operation in accordance with slave profile 7.4
(multibit data)

If you wish to use slave profile 7.4, you will require an AS-In-
terface master which supports this profile (e.g. the AS-Inter-
face master from Siemens type CP 343-2). Explanations on
this can be found in the documentation for your AS-Interface
master.

Information on operating in accordance with slave profile 7.4
can be found in Appendix A.

Содержание Soft Stop SPC11 Series







































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды