Festo Soft Stop SPC11 Series Скачать руководство пользователя страница 69 | Manualshive

Страница: 69 / 134

Festo Soft Stop SPC11 Series Скачать руководство пользователя страница 69

4. Commissioning

4-9

Festo P.BE-SPC11-SYS-ASI-EN en 0203NH

4. Hold the Enter key pressed down for at least 2 seconds.

(

>

2 s). The value will then be transferred to the SPC11

and the cushioning stage will be shown (here 0). This is
shown by the letter C (

C

ushioning stage).

(C.00)

5. Now set the desired cushioning stage with the b/-

(see axis-specific supplement), e.g. 04.

(C.04)

6. Hold the Enter key pressed down for at least 2 seconds.

(

>

2 s). The value will then be transferred to the SPC11

and the system parameter will be shown (here 0).

(S.00)

7. Now set the system parameter valid for your structure

with the b/- (see axis-specific supplement),
e.g. 01.

(S.01)

8. Hold the Enter key pressed down for at least 2 seconds.

(

>

2 s). The value will then be transferred to the SPC11

and the readiness to carry out the teach procedure will be
indicated by a flashing “t.” The three parameters are then
saved and pre-parametrizing (in the office) is completed.

The t flashes.

When all prerequisites for carrying out the teach procedure
have been made (see sections 4.3.1), the teach procedure
can be started (see sections 4.3.2).

9. If you wish to conclude pre-commissioning, switch off the

operating voltage.

«
...
67
68
69
70
71
...
»

Содержание Soft Stop SPC11 Series







































































































































Отзывы:

Нет отзывов