manualshive.com logo in svg

Festo Soft Stop SPC11 Series, Системное руководство

Поделиться
Скачать
Festo Soft Stop SPC11 Series Скачать руководство пользователя страница 24

1. Summary of components

1-10

Festo P.BE-SPC11-SYS-ASI-EN en 0203NH

1.4

Method of working as an AS-Interface slave

The SPC11 can be operated as a standard slave with 4-bit I/O
data and in accordance with slave profile 7.4 (multibit data).
Different functions are available here via the AS-Interface
bus.

Profile used

Functions supported via the
AS-Interface bus

Standard slave with
4-bit I/O data

– Standard operating functions

Accessing the desired end positions and
intermediatee positions with feedback

Slave profile 7.4
(multibit data)

– Extended operating functions

(e.g. load new intermediate position)

– Commissioning functions
– Diagnostic functions

Standard slave with
4-bits I/O data

When the SPC11 is operated as a standard slave with 4-bit
I/O data, only standard operating functions are available.
The SPC11 is controlled via 4-bit I/O data. The 4 possible
positions are accessed via the 4 input bits. When the the
relevant position is reached, the feedback is made via the
4 output bits.

Commissioning functions are not supported in this operating
mode. Commissioning must be carried out via the keyboard
with the AS-Interface cable (bus) disconnected or without
power.

Slave profile 7.4

Operation in accordance with slave profile 7.4 enables addi-
tional operating functions and parametrizing, commission-
ing and diagnosis of the SPC11 via the AS-Interface bus. If
you wish to use slave profile 7.4, you will require an AS-In-
terface master which supports this profile.

Содержание Soft Stop SPC11 Series







































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды