Festo Soft Stop SPC11 Series Скачать руководство пользователя страница 59

Страница: 59 / 134

3. Installation

3-31

Festo P.BE-SPC11-SYS-ASI-EN en 0203NH

3.3.5 Connecting the proportional directional control valve and the

measuring system

Connecting the measuring system

Use only the permitted combinations of drives and measuring
systems approved of by Festo for the SPC11. The connecting
cable for the measuring system is firmly connected to the
SPC11.

Please note

Interference due to electromagnetic influences can be
avoided if a short cable is used. Use only the original
cable.

Observe also, where applicable, the operating instructions for
the measuring system.

Fasten the plug with the aid of the integrated screw, in order
to prevent unintentional loosening, e.g. due to shock.

Connecting the proportional directional control valve

The valve connection provides the power supply for the valve
and the control voltage for positioning the valve slide.

Use only the original cable for connecting the valve.

Type designation

Cable length

KMPYE-AIF-1-GS-GD-2

2 m

KMPYE-AIF-1-GS-GD-0.3

0.3 m

Содержание Soft Stop SPC11 Series







































































































































Результаты поиска

Содержание Soft Stop SPC11 Series

Отзывы:

Бренды по названию

Популярные бренды

Festo Soft Stop SPC11 Series, Системное руководство

Результаты поиска

Содержание Soft Stop SPC11 Series

Отзывы:

Бренды по названию

Популярные бренды