manualshive.com logo in svg

Festo Soft Stop SPC11 Series, Системное руководство, Страница: 119 / 134

Поделиться
Скачать
Festo Soft Stop SPC11 Series Скачать руководство пользователя страница 119

A. Operating the SPC11 in accordance with slave profile 7.4

A-5

Festo P.BE-SPC11-SYS-ASI-EN en 0203NH

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

Reserved

Reserved

Quit
faults

Start the
teach
procedure

Accept
the actual
position
as P.04

Accept
the actual
position
as P.03

Move to
the left

Move to
the right

Order

Description

Move to the right

All the time this bit is set, the drive will move in the direction of the
measuring system zero point.

Move to the left

All the time this bit is set, the drive will move away from the measuring
system zero point.

Accept the actual position
as P.03

When this bit is set (transition from 0 to 1) the current position will be
accepted as the intermediate position P.03.

Accept the actual position
as P.04

When this bit is set (transition from 0 to 1) the current position will be
accepted as the intermediate position P.04.

Start the teach procedure

When this bit is set (transition from 0 to 1) the teach procedure will be
started.

Quit faults

When this bit is set (transition from 0 to 1) the current fault will be
quitted.

Содержание Soft Stop SPC11 Series







































































































































Отзывы:

Нет отзывов