Endress+Hauser Proline t-mass 65 PROFIBUS DP Скачать руководство пользователя страница 28

Страница: 28 / 106

Installation

Proline t-mass 65 PROFIBUS DP

3.4

Post-installation check

Perform the following checks after installing the measuring device in the pipe:

Device condition and specifications

Notes

Is the device damaged (visual inspection)?

–

Does the device correspond to specifications at the measuring point, including
process temperature and pressure, ambient temperature, measuring range, etc.?
Check the name plate.

→

Page 92 ff.

Installation

Notes

Correct alignment of pipe/gasket/flowmeter body?

→

Page 12

Correct pipe internal diameter and surface finish/quality?

→

Page 12

Is the orientation chosen for the sensor correct, in other words suitable for sensor
type, fluid properties and fluid temperature?

→

Page 13

Is there sufficient upstream and downstream length from the measurement point?

→

Page 14 ff.

Correct installation of flow conditioner (if fitted)?

→

Page 16 ff.

Does the arrow on the sensor nameplate match the direction of flow through the
pipe?

→

Page 17

Correct insertion sensor depth (insertion version only)?

→

Page 18

Process environment / process conditions

Notes

Is the measuring device protected against moisture and direct sunlight?

–

Is the measuring device protected against overheating?

→

Page 23

Is the measuring device protected against excessive vibration?

→

Page 24, 96

Check gas conditions (e. g. purity, dryness, cleanliness)

–

Содержание Proline t-mass 65 PROFIBUS DP











































































































Результаты поиска

Содержание Proline t-mass 65 PROFIBUS DP

Отзывы:

Похожие инструкции для Proline t-mass 65 PROFIBUS DP

Бренды по названию

Популярные бренды

Endress+Hauser Proline t-mass 65 PROFIBUS DP, Руководство по эксплуатации

Результаты поиска

Содержание Proline t-mass 65 PROFIBUS DP

Отзывы:

Похожие инструкции для Proline t-mass 65 PROFIBUS DP

Бренды по названию

Популярные бренды