Emerson Rosemount X-STREAM O2 Transmitter Скачать руководство пользователя страница 110

Страница: 110 / 174

Hazardous Area

X-STREAM O

Transmitter

6-12

Instruction Manual

IM-106-910C, Rev. 1.0

November 2009

Cell Installation

Use the following instructions to install a new O

sensing cell.

1. Apply anti-seize compound to flange of new cell, Figure 6-9.
2. Place new corrugated washer onto cell flange with the ridges pointing

up as shown in Figure 6-9. Fit is tight. Hold gasket in place with one

finger then "walk" the gasket in place using another finger. Use care not

to bend or kink the washer.

3. Apply anti-seize compound to exposed surface of corrugated washer.
4. Install the new cell (4, Figure 6-1) with corrugated washer (3) into the

end of sensor core assembly (1).

5. Apply anti-seize compound to threads of cell retainer (5) and mating

threads in heater housing.

6. Thread cell retainer (5) into the heater housing. Use cell removal tool

and 1/4 inch diameter pin to tighten cell retainer to 30 ft-lbs (40,67 N

m).

7. Tighten screw (24, Figure 6-5) to secure contact and thermocouple

assembly (5).

8. Remove the setscrews from diffuser (6, Figure 6-1).
9. Apply anti-seize compound to threads of setscrews and thread

setscrews three turns into diffuser.

10. Install diffuser (6) in the same orientation as the old diffuser. Install and

tighten the diffuser setscrews.

11. Apply a light coating of silicone grease onto the o-ring of sensor core

assembly (1).

12. Install sensor core assembly (1) in probe tube (7).
13. Install and tighten three screws (20) to secure sensor core assembly (1)

inside probe tube (7).

14. Connect the sensor core plug to electronics board (8).

15. Re-connect the cal gas and reference air hoses as shown in Figure 6-3.

The cal gas hose connects between the hose ports marked "C". The

reference air hose connects between the hose ports marked "R".

16. Recalibrate the probe per "O2 Calibration" in Section 4 of this instruction

manual.

If installing a ceramic or Hastelloy diffuser be sure to orient the rounded deflector so it points

upstream relative to the flue gas air flow.

Do not use excessive force when installing the reference air or cal gas hose onto the

connecting tube. Using excessive force can buckle the stainless steel tubing.

Failure to correctly install the hoses may allow gas leakage and result in erroneous O

readings. Be sure to correctly install the calibration gas and reference air hoses.

Содержание Rosemount X-STREAM O2 Transmitter















































































































































































Результаты поиска

Содержание Rosemount X-STREAM O2 Transmitter

Отзывы:

Похожие инструкции для Rosemount X-STREAM O2 Transmitter

Бренды по названию

Популярные бренды

Emerson Rosemount X-STREAM O2 Transmitter, Инструкция по эксплуатации

Результаты поиска

Содержание Rosemount X-STREAM O2 Transmitter

Отзывы:

Похожие инструкции для Rosemount X-STREAM O2 Transmitter

Бренды по названию

Популярные бренды