Emerson Rosemount X-STREAM O2 Transmitter Скачать руководство пользователя страница 80

Страница: 80 / 174

Hazardous Area

X-STREAM O

Transmitter

4-14

Instruction Manual

IM-106-910C, Rev. 1.0

November 2009

Field Communicator
Signal Line Connections
(with Xi)

Whenever the Hazardous Area X-STREAM O

Transmitter includes the Xi

Enhanced Interface option, be sure to connect the 375 Field Communicator

only to the 4 to 20 mA signal loop wiring between the Xi Enhanced Interface

and the control room or data acquisition system as shown in Figure 4-6.

When working at the Xi, the 375 Field Communicator can be connected

directly to test points TP21 and TP22 on the Xi Enhanced Interface I/O Board.

The AM+ and AM- test points are provided to monitor the 4-20 mA signal

without breaking into the loop.

Figure 4-6. 375 Field Communicator Connection at the Xi Enhanced Interface

The Xi Enhanced Interface communicates with the transmitter via HART

communications riding on the 4 to 20 mA signal coming from the transmitter.

Xi communication with the transmitter will be disrupted if a 375 Field

Communicator is connected to the signal loop between the transmitter and

the Xi Enhanced Interface.

Do not

use the H1 and H2 terminals or connect the HART in the probe (transmitter-to-Xi)

4-20 mA signal loop if your system includes the Xi Enhanced Interface. Xi communication

with the transmitter will be disrupted if a 375 Field Communicator is connected to the H1

and H2 terminals or to the transmitter-to-Xi signal loop.

Содержание Rosemount X-STREAM O2 Transmitter















































































































































































Результаты поиска

Содержание Rosemount X-STREAM O2 Transmitter

Отзывы:

Похожие инструкции для Rosemount X-STREAM O2 Transmitter

Бренды по названию

Популярные бренды

Emerson Rosemount X-STREAM O2 Transmitter, Инструкция по эксплуатации

Результаты поиска

Содержание Rosemount X-STREAM O2 Transmitter

Отзывы:

Похожие инструкции для Rosemount X-STREAM O2 Transmitter

Бренды по названию

Популярные бренды