Emerson Rosemount X-STREAM O2 Transmitter Скачать руководство пользователя страница 103

Страница: 103 / 174

Instruction Manual

IM-106-910C, Rev. 1.0

November 2009

6-5

Hazardous Area

X-STREAM O

Transmitter

X-STREAM O

TRANSMITTER
PROBE REPAIR

Each of the procedures that follow details how to remove and replace a

specific component of the Hazardous Area X-STREAM O

Transmitter. Part

replacement kits are available for each of the transmitter components

replaced in this repair section. Refer to Section 7: Replacement Parts for kit

part numbers.

Sensor Core or Diffuser
Replacement

1. See Figure 6-1. Loosen and remove the lock clip (22) from the cover

lock slots.

2. Remove left housing cover (18) to access the core.
3. Remove three screws (19).
4. Disconnect the sensor connector plug from electronics board (8). Pull

on the connector lanyard as shown in Figure 6-2.

NOTE

A connector plug with lanyard replacement kit is available in case the sensor

connector plug is worn or damaged. Refer to Section 7: Replacement Parts

for the replacement kit part number.

Figure 6-2. Disconnecting

Connector Plug

It is recommended that the X-STREAM be removed from the stack for all service activities.

The unit should be allowed to cool and be taken to a clean work area. Failure to comply may

cause severe burns.

Disconnect and lock out power before working on any electrical components. There is

voltage up to 240 VAC.

Содержание Rosemount X-STREAM O2 Transmitter















































































































































































Результаты поиска

Содержание Rosemount X-STREAM O2 Transmitter

Отзывы:

Похожие инструкции для Rosemount X-STREAM O2 Transmitter

Бренды по названию

Популярные бренды

Emerson Rosemount X-STREAM O2 Transmitter, Инструкция по эксплуатации

Результаты поиска

Содержание Rosemount X-STREAM O2 Transmitter

Отзывы:

Похожие инструкции для Rosemount X-STREAM O2 Transmitter

Бренды по названию

Популярные бренды