Emerson Rosemount X-STREAM O2 Transmitter Скачать руководство пользователя страница 111

Страница: 111 / 174

Instruction Manual

IM-106-910C, Rev. 1.0

November 2009

6-13

Hazardous Area

X-STREAM O

Transmitter

Replace Contact &
Thermocouple Assembly

1. See Figure 6-1. Loosen and remove the lock clip (22) from the cover

lock slots.

2. Remove left housing cover (18) to access the core.
3. Remove three screws (19).
4. Disconnect the sensor connector plug from electronics board (8). Pull

on the connector lanyard as shown in Figure 6-2.

5. Disconnect black heater wires from the connector plug.
6. Remove screw (24, Figure 6-5).

7. Pull lightly on contact pad assembly (5). If it does not slide free from

guide tube assembly (14), twist the assembly to break the temporary

"weld" between the contact pad and cell (4).

8. Remove contact and thermocouple assembly (5) from sensor core

assembly.

9. Slide the new contact and thermocouple assembly (5) into the sensor

core base (7). A twisting motion can be used to ease installation.

10. Install screw (24) through the ground lead terminal and retaining plate

into the core base (7). Tighten the screw.

11. Reconnect black heater wires at the connector plug. Refer to

Figure 6-10. Polarity on the two black wires is not specified.

12. Re-connect sensor core plug to the electronics board (8, Figure 6-1).
13. Recalibrate the probe per "O2 Calibration" in Section 4 of this manual.

Figure 6-10. Contact and

Thermocouple Wiring

If the contact and thermocouple assembly does not come free with a light pull, do not pull

harder. Failure to correctly free the contact pad from the cell may result in damage to the

contact and thermocouple assembly.

Содержание Rosemount X-STREAM O2 Transmitter















































































































































































Результаты поиска

Содержание Rosemount X-STREAM O2 Transmitter

Отзывы:

Похожие инструкции для Rosemount X-STREAM O2 Transmitter

Бренды по названию

Популярные бренды

Emerson Rosemount X-STREAM O2 Transmitter, Инструкция по эксплуатации

Результаты поиска

Содержание Rosemount X-STREAM O2 Transmitter

Отзывы:

Похожие инструкции для Rosemount X-STREAM O2 Transmitter

Бренды по названию

Популярные бренды